QLogic 1GB iSCSI TOE Expansion Card for IBM eServer BladeCenter SCSI Stor Miniport Driver 2.1.1.5 and Networking Driver 2.0.0.0 QMC4052Stor2115Net2000.txt Version 1.00 6/15/05 ________ CONTENTS ________ 1.0 Overview 2.0 Change History 3.0 Installation and Setup Instructions 4.0 Configuration Information 5.0 Known Issues 6.0 Unattended Mode 7.0 Web Sites and Support Phone Number 8.0 Trademarks and Notices 9.0 Disclaimer _______________ 1.0 Overview _______________ This README describes the current SCSI Stor Miniport driver version 2.1.1.5 and Networking driver version 2.0.0.0 package for the QLogic 1GB iSCSI TOE Expansion Card and procedure for updating the drivers on the expansion card. ____________________ 2.0 Change History ____________________ QLogic iSCSI Expansion Card SCSI Miniport Driver Version 2.1.1.5 and Networking Driver 2.0.0.0 ---------------------------------------------------------------- -Initial Version _________________________________________ 3.0 Installation Instructions _________________________________________ This section is divided into the following four sections: . Initial OS installation with the QLogic iSCSI Adapter as Boot or as Add-On . Adding the QLogic iSCSI Adapter to the Existing OS . Updating the Existing Driver . Removing the driver NOTE: . The QLogic iSCSI Adapter adapter is a multifunction device. When installed in a PNP system, the OS will detect two functions for each adapter: Ethernet Controller and Network Controller. The Network Controller refers to the iSCSI function. ====================================================================== 3.1. Initial OS installation with the QLogic iSCSI Adapter as Boot or as Add-On ------------------------------------------------------------------- NOTE: . You must create a driver disk (see section 4) when installing the OS and the QLogic iSCSI Adapter. You cannot install the QLogic iSCSI Adapter driver directly from the QLogic CD. Perform the following steps to install Windows with the QLogic iSCSI Adapter driver when the QLogic iSCSI Adapter is attached to a bootable device: 1. Start the Windows installation procedure using the Setup disks or CD. 2. If you are booting using the Windows installation CD, press F6 when the following message displays: "Press F6 if you want to install a third party SCSI or RAID" After all the standard devices have been loaded, press S to Specify Additional Device. Go to step 5. 3. If you are booting from the Windows installation floppy disks, after the standard devices have been detected and configured, press S to specify additional Device. 4. Select Other and press ENTER. 5. Insert the QLogic driver disk created in section 4 and press ENTER. 6. Select the QLogic iSCSI Adapter, then press ENTER. 7. Continue with standard installation procedure. ====================================================================== 3.2. Adding the QLogic iSCSI Adapter to the Existing OS ------------------------------------------------------- Perform the following steps to add the QLogic iSCSI Adapter's driver to an existing Windows system: 1. Install the QLogic iSCSI Adapter in the appropriate slot on your computer. 2. Restart or power up your computer, and log in as Administrator. 3. When your computer powers up, Windows detects the newly installed device, then displays the Found New Hardware Wizard with Ethernet Controller message. The Found New Hardware Wizard program is launched to begin installing the QLogic Ethernet NDIS Miniport driver for the QLogic iSCSI Adapter. 4. Select Install from a list or specific location (Advanced). click Next. 5. Select the Search for the best driver in these locations option, and type or browse the path to the QLogic driver directory. For example: A:\ 6. Insert the QLogic driver disk in an appropriate drive, and click next. 7. In the Completing the Found New Hardware Wizard dialog box click Finish. 8. Windows will detect the second Ethernet Controller. Repeat steps 4-7 to install the QLogic Ethernet NDIS Miniport driver for the second networking function. 9. Windows will display the Found New Hardware Wizard with Network Controller message. The Found New Hardware Wizard program is launched to begin installing the SCSI Stor Miniport driver for the QLogic iSCSI Adapter. 10. Select Install from a list or specific location (Advanced). click Next. 11. Select the Search for the best driver in these locations option, and type or browse the path to the QLogic driver directory. For example: A:\ 12. Insert the QLogic driver disk in an appropriate drive, and click Next. 13. Click Finish on the Completing the Found New Hardware Wizard dialog box. 14. Windows will detect the second Network Controller. Repeat steps 10-13 to install the SCSI Stor Miniport driver for the second iSCSI function. ====================================================================== 3.3. Updating the Existing Driver --------------------------------- Perform the following steps if the QLogic iSCSI Adapter's driver is already installed and you want to install an updated version of the driver: 1. Start the Device Manager by clicking Start, pointing to Settings, clicking Control Panel, double clicking System applet, clicking Hardware tab, and clicking the Device Manager button. 2. Use scroll bar to scroll down the list of hardware types, double click the SCSI and RAID controller. 3. Select QLogic iSCSI Adapter from the devices list and then click Properties. 4. Click the Driver tab, and then click Update Driver to start the Upgrade Device Driver Wizard. Click Next. 5. Select Install from a list or specific location(Advanced). click Next. 6. Select Don't search I will choose the driver to install. Click Next. 7. Insert the QLogic driver disk in an appropriate drive, and click Have Disk. 8. In the Install From Disk dialog box Copy manufacturer's files from field, type or browse the path to the QLogic driver directory. For example: A:\ 9. Click OK in the Install From Disk dialog box 10. When the Hardware Update Wizard/Select a Device Driver dialog box appears, click Next. 11. When the Hardware Installation dialog box displays, select Continue Anyway. 12. Click Finish on the Hardware Update Wizard/Completing the Hardware Update Wizard. 13. Repeat steps 1-12 for the second iSCSI adapter port. ====================================================================== 3.4. Removing the Driver ---------------------- The driver does not need to be uninstalled to uninstall the QLogic iSCSI Adapter device. Simply power down your computer and remove the adapter from your computer according to the manufacturer's instructions. NOTE: . You do not have to use the Device Manager or the Hardware Wizard to uninstall the QLogic iSCSI Adapter. After you have removed the QLogic iSCSI Adapter and restarted your computer, Windows recognizes that it has been removed. _______________________________ 4.0 Configuration Information _______________________________ Detailed information on configuring the QLogic iSCSI HBA can be found in the SANsurfer online help available from the QLogic website. _______________________________ 5.0 Known Issues _______________________________ No known issues _____________________ 6.0 Unattended Mode _____________________ This package does not support Unattended Mode ________________________________________ 7.0 WEB Sites and Support Phone Number ________________________________________ IBM Support Web Site: http://www.ibm.com/pc/support IBM Marketing Netfinity Web Site: http://www.pc.ibm.com/netfinity If you have any questions about this update, or problems applying the update go to the following Help Center World Telephone Numbers URL: 1-800-772-2227 http://www.pc.ibm.com/qtechinfo/YAST-3P2QYL.html. ____________________________ 8.0 Trademarks and Notices ____________________________ The following terms are trademarks of the IBM Corporation in the United States or other countries or both: IBM BladeCenter eServer Microsoft, Windows, and Windows NT are trademarks of Microsoft Corporation in the United States, other countries, or both. Linux is a registered trademark of Linus Torvalds. Intel trademarks or registered trademarks are trademarks of Intel Corporation. Other company, product, and service names may be trademarks or service marks of others. ________________ 9.0 Disclaimer ________________ THIS DOCUMENT IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND. IBM DISCLAIMS ALL WARRANTIES, WHETHER EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE AND MERCHANTABILITY WITH RESPECT TO THE INFORMATION IN THIS DOCUMENT. BY FURNISHING THIS DOCUMENT, IBM GRANTS NO LICENSES TO ANY PATENTS OR COPYRIGHTS. Note to Government Users Note to U.S. Government Users -- Documentation related to restricted rights -- Use, duplication or disclosure is subject to restrictions set forth in GSA ADP Schedule Contract with IBM Corporation.