IBM System x3550 Baseboard Management Controller (BMC) Update CD ROM
Version 1.09 build ID GFBT25AUS

System machine type 7978

CONTENTS
________

1.0  Overview
2.0  Installation and Setup Instructions
3.0  Configuration Information
4.0  Unattended Mode
5.0  Web Sites and support phone Number
6.0  Trademarks and Notices
7.0  Disclaimer



1.0  Overview
________________________

This CDROM will update the Baseboard Management Controller (BMC) firmware
only.  It will not affect any device drivers.


        1.1  To use this CDROM, perform the following steps:

             a).  Make sure BIOS version 1.00, or later, is installed.

             b).  Insert this CDROM into the CDROM drive and
                  restart the system.  If your system does not boot from
                  the CDROM, use POST/BIOS setup to configure the
                  CDROM drive as a boot device.  Please refer to the
                  Server Library that was included with your system for
                  additional information.

             c).  Once your system boots, the BMC update firmware update
                  will execute automatically.

             d).  When you are finished using the utility, remove the
                  CDROM from the CDROM drive and restart your system.

        1.2  Limitations

             If there is an error in loading the BMC firmware retry
             loading the software by repeating the instructions in
             section 1.1.

        1.3  Enhancements

             - IPMI

        1.4. Level of Recommendations and Prerequisites for the
             update:

             - BIOS version 1.00, or later, must be installed prior to
               installing this BMC firmware update.

             - A full tape backup should be completed and verified
               prior to running this, or any other system upgrade.

             - RAID configuration should be saved to a diskette:
               see the "Hardware Maintenance Manual" for more details.

        1.5  Dependencies:

             - none


2.0  Installing and Setup Instructions
______________________________________

To install the firmware on this CDROM, perform the following steps:

        2.1  Make sure BIOS version 1.00, or later, is installed.
        2.2  Make sure your system is powered down.
        2.3  Insert the CDROM in the CDROM drive.
        2.4  Power on your system to boot from CDROM drive.
             If your system does not boot from the CDROM, use
             POST/BIOS setup utility to configure the CDROM drive
             as a boot device.
        2.5  Once your system boots, the BMC update firmware update
             will execute automatically.
        2.6  When the update completes, remove the CDROM from the drive
             and restart the system.
        2.7  You may clear the BMC's SEL.


3.0  Configuration Information
______________________________________

        There is no configuration information necessary.


4.0     Unattended Mode
_______________________

        This update utility does not support unattended installations but there are other
        ways to incorporate unattended installations of this code. Check the UpdateXpress
        CD for availability of unattended installs of this firmware.  (The UpdateXpress
        CD is downloadable from http://www.ibm.com (use the search function to find
        "UpdateXpress").


5.0     WEB Sites and Support Phone Number
__________________________________________

        5.1  IBM Support Web Site:
             http://www.pc.ibm.com/support

        5.2  IBM System x Web Site:
             http://www.ibm.com/system/x

        5.3  If you have any questions about this update, or
             problems applying the update, go to the following
             Help Center World Telephone Numbers and URL:
             http://www.pc.ibm.com/qtechinfo/YAST-3P2QYL.html.


6.0.    TradeMarks and Notices
______________________________

        6.1  The following terms are trademarks of the IBM
             Corporation in the United States, or other countries
             or both:
                         * IBM
                         * Netfinity
                         * Netfinity Manager
                         * Advanced System Management

             Other company, product, and service names may be
             trademarks or service marks of others.


7.0.    Disclaimer
__________________

        7.1  THIS DOCUMENT IS PROVIDED "AS IS" WITHOUT WARRANTY OF
             ANY KIND.  IBM DISCLAIMS ALL WARRANTIES, WHETHER EXPRESS
             OR IMPLIED, INCLUDING WITHOUT LIMITATION, THE IMPLIED
             WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE AND
             MERCHANTABILITY WITH RESPECT TO THE INFORMATION IN
             THIS DOCUMENT.  BY FURNISHING THIS DOCUMENT, IBM
             GRANTS NO LICENSES TO ANY PATENTS OR COPYRIGHTS.

        7.2  Note to Government users:

             Note to U.S. Government users-- Documentation related
             to restricted rights-- Use, duplication and disclosure
             is subject to restrictions set forth in GSA ADP Schedule
             Contract with IBM Corporation.


(C) Copyright International Business Machines Corporation 2006.
    All rights reserved.