IBM eserver xSeries 460 Remote Supervisor Adapter II Update for Linux System 8872 Version 1.04, Build ID: ZUEP26A, Revision 16 CONTENTS ________ 1.0 Overview 2.0 Change History 3.0 Installation and Setup Instructions 4.0 Unattended Mode 5.0 Web Sites and support phone Number 6.0 Trademarks and Notices 7.0 Disclaimer 1.0 Overview ________________________ 1.1 This will update the IBM Remote Supervisor Adapter II software only. It will not affect any device drivers. 1.2 Limitations If there is an error in loading the IBM Remote Supervisor Adapter II software, retry loading the software by repeating the instructions in section 3.0. 1.3 Enhancements - none 1.4. Level of Recommendations and Prerequisites for the update: - Multi-lun support is needed in order to mount more then one remote drive simultaneously. The linux kernel 2.4.20 and later have the appropriate multi-lun support, however this support needs to be enabled at kernel build time. Currently, only the SLES 8.0 SP3 distribution has multi-Lun support available and enabled. RedHat AS 3.0 has a 2.4.21 kernel, but does not have multi-lun support enabled by default. 1.5 Dependencies: - none 2.0 Change History ________________________ IBM Remote Supervisor Adapter II Update Version 1.04, ZUEP26A - Added support for 4-way & 8-way multinode configurations of machine type 8872. IBM Remote Supervisor Adapter II Update Version 1.03, ZUEP25A - Log hard drive removals. - Log CPU/VRM Configuration errors. IBM Remote Supervisor Adapter II Update Version 1.02, ZUEP22A - Added support for machine type 8872. - Added support for additional sensors and events. IBM Remote Supervisor Adapter II Update Version 1.01, ZUEP18B - Corrected Component VPD list to include all components and correctly display data. - Corrected the information placed in the System Event Log for some SMI Events. - Added support to handle IPMI sensor changes in the BMC. IBM Remote Supervisor Adapter II Update Version 1.00, ZUEP16A - First release 3.0 Installing and Setup Instructions ______________________________________ This utility will update the IBM Remote Supervisor Adapter II software under the Linux Operating System. It requires the installation of the correct Remote Supervisor Adapter II for Linux device driver. 3.1 Performing this code update (command line) ________________________________________________ - Run the "IBM xSeries 366 Linux Remote Supervisory Adapter II Update" from a command line with the "-s" parameter. "./.sh -s" where .sh is the downloaded update. 3.2 Extracting the Linux update files (command line) __________________________________________________ - Run the "IBM xSeries 366 Linux Remote Supervisor Adapter II Update" with the following command line: "./.sh -x " where .sh is the downloaded update and is the path to which the Linux update files will be extracted. NOTE: The following message is shown on RedHat Enterprise Linux 3.0 and other distributions that do not install the compatibility libstdc++ library. ./lflash: error while loading shared libraries: libstdc++-libc6.1-1.so.2: cannot open shared object file: No such file or directory. If the above message is shown, install the compat-libstdc++*.rpm that was included on the distribution media. - The files extracted are all the files that are necessary to perform a RSAII firmware update under Linux. Run "./lflash -r" from a command line to update RSAII firmware on 32-bit Linux or "./lflash64 -r" on 64-bit Linux. 4.0 Unattended Mode ________________________ Extracting the Linux update files (command line) __________________________________________________ - Run the "IBM xSeries 366 Linux Remote Supervisor Adapter II Update" with the following command line: ".exe -s -a -x " where .exe is the downloaded update and is the path to which the Linux update files will be extracted. NOTE: The following message is shown on RedHat Enterprise Linux 3.0 and other distributions that do not install the compatibility libstdc++ library. ./lflash: error while loading shared libraries: libstdc++-libc6.1-1.so.2: cannot open shared object file: No such file or directory. If the above message is shown, install the compat-libstdc++*.rpm that was included on the distribution media. - The files extracted are all the files that are necessary to perform a RSAII firmware update under Linux. Run "./lflash -r" from a command line to update RSAII firmware. 5.0 WEB Sites and Support Phone Number _________________________________________ 5.1 IBM Support Web Site: http://www.pc.ibm.com/support 5.2 IBM eserver xSeries Web Site: http://www.ibm.com/eserver/xseries 5.3 If you have any questions about this update, or problems applying the update, go to the following Help Center World Telephone Numbers and URL: http://www.pc.ibm.com/qtechinfo/YAST-3P2QYL.html. 6.0. TradeMarks and Notices ______________________________ 6.1 The following terms are trademarks of the IBM Corporation in the United States, or other countries or both: * IBM * Advanced System Management Other company, product, and service names may be trademarks or service marks of others. 7.0. Disclaimer __________________ 7.1 THIS DOCUMENT IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND. IBM DISCLAIMS ALL WARRANTIES, WHETHER EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE AND MERCHANTABILITY WITH RESPECT TO THE INFORMATION IN THIS DOCUMENT. BY FURNISHING THIS DOCUMENT, IBM GRANTS NO LICENSES TO ANY PATENTS OR COPYRIGHTS. 7.2 Note to Government users: Note to U.S. Government users-- Documentation related to restricted rights-- Use, duplication and disclosure is subject to restrictions set forth in GSA ADP Schedule Contract with IBM Corporation.