IBM eserver xSeries Baseboard Management Controller (BMC) Update Diskette Version 1.06 System 8837 CONTENTS ________ 1.0 Overview 2.0 Change History 3.0 Installation and Setup Instructions 4.0 Unattended Mode 5.0 Web Sites and support phone Number 6.0 Trademarks and Notices 7.0 Disclaimer 1.0 Overview ________________________ This diskette will update the Baseboard Management Controller (BMC) firmware and sensor data records (SDRs) only. It will not affect any device drivers. 1.1 To use this diskette, perform the following steps: a). Make sure BIOS version 1.00, or later, is installed. b). Insert this diskette into the diskette drive and restart the system. If your system does not boot from the diskette, use POST/BIOS setup to configure the diskette drive as a boot device. Please refer to the Server Library that was included with your system for additional information. c). Once your system boots, a ramdrive will be created, the appropriate files will be copied to this ramdrive and the BMC update firmware update will execute automatically. d). When you are finished using the utility, remove the diskette from the diskette drive and restart your system. 1.2 Limitations If there is an error in loading the BMC firmware or SDRs retry loading the software by repeating the instructions in section 1.1. 1.3 Enhancements - IPMI 1.4. Level of Recommendations and Prerequisites for the update: - BIOS version 1.00, or later, must be installed prior to installing this ISMP firmware update. - A full tape backup should be completed and verified prior to running this, or any other system upgrade. - RAID configuration should be saved to a diskette: see the "Hardware Maintenance Manual" for more details. 1.5 Dependencies: - none 2.0 Change History ______________________________________ Baseboard Management Controller Version 1.06 - Fix NMI handling - Filter out misleading voltage and temperature readings - Change SCSI harddrive sensors to correctly correspond to their designated drives - Change in the architecture and corresponding code to detect and report true CPU errors - Fix so that the corresponding PET severities are sent out - Fix FRU entries within the FRU locator table as well as other various entries within the SDR table - Added fix for unexpected watchdog restart Baseboard Management Controller Version 1.05 - Changed max ping packet size from 277 to 262 bytes Baseboard Management Controller Version 1.04 - Add support for SysRq keys in Linux environment - Fix for IPMI sequencing numbers causing SOL dropped sessions - SOL optimization code to increase SOL bandwidth and throughput - Fix for the following scenario: shared COMport during SOL, and then switch COMport to dedicated causes a 1601 error - Fix for oversized ping packets causing BMC reset (max ping packet is now 277 bytes) Baseboard Management Controller Version 1.03 - Changed the User Priviledge Limit for Null User ID per Baseboard Management Controller System Specification. Baseboard Management Controller Version 1.02 - Alert Policy Table entry fixes - SDR records cleanup - Fix: SYS_HEALTH_QUERY command related issues - Fix: Made sure to log power down events - PS error logging fixes - Fix: defects found through PCI BEST cases tests Baseboard Management Controller Version 1.01 - Original Release 3.0 Installing and Setup Instructions ______________________________________ To install the firmware on this diskette, perform the following steps: 3.1 Make sure BIOS version 1.00, or later, is installed. 3.2 Make sure your system is powered down. 3.3 Insert the diskette in the diskette drive. 3.4 Power on your system to boot from diskette drive. If your system does not boot from the diskette, use POST/BIOS setup utility to configure the diskette drive as a boot device. 3.5 Once your system boots, a ramdrive will be created, the appropriate files will be copied to this ramdrive and the BMC update firmware update will execute automatically. 3.6 When the update completes, remove the diskette from the drive and restart the system. 4.0 Unattended Mode _______________________ This update utility does not support unattended installations but there are other ways to incorporate unattended installations of this code. Check the UpdateXpress CD for availability of unattended installs of this firmware. (The UpdateXpress CD is downloadable from http://www.ibm.com (use the search function to find "UpdateXpress"). 4.1 Steps for unattended mode - Boot to DOS - Create a directory for your BMC flash files. - Copy the following files from the"IBM xSeries 336 BMC Baseboard Management Contoller Flash Disk" to the same directory on some media capable of storing 2.5MB of data. - "update.bat "flash.exe" "bmc_cfg.exe" "fullfw.mot" "intf.ini" - From the directory just copied to, run "update.bat" 5.0 WEB Sites and Support Phone Number __________________________________________ 5.1 IBM Support Web Site: http://www.pc.ibm.com/support 5.2 IBM eserver xSeries Web Site: http://www.ibm.com/eserver/xseries 5.3 If you have any questions about this update, or problems applying the update, go to the following Help Center World Telephone Numbers and URL: http://www.pc.ibm.com/qtechinfo/YAST-3P2QYL.html. 6.0. TradeMarks and Notices ______________________________ 6.1 The following terms are trademarks of the IBM Corporation in the United States, or other countries or both: * IBM * Netfinity * Netfinity Manager * Advanced System Management Other company, product, and service names may be trademarks or service marks of others. 7.0. Disclaimer __________________ 7.1 THIS DOCUMENT IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND. IBM DISCLAIMS ALL WARRANTIES, WHETHER EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE AND MERCHANTABILITY WITH RESPECT TO THE INFORMATION IN THIS DOCUMENT. BY FURNISHING THIS DOCUMENT, IBM GRANTS NO LICENSES TO ANY PATENTS OR COPYRIGHTS. 7.2 Note to Government users: Note to U.S. Government users-- Documentation related to restricted rights-- Use, duplication and disclosure is subject to restrictions set forth in GSA ADP Schedule Contract with IBM Corporation. Appendix A: Package Specific Installation Instruction This update is packaged as a self-extracting PackageForTheWeb (PFTW) executable file. To unpack, this update requires that your TEMP environment variable be set to a path with read/write access. You must be logged in as an administrator. The package update log, ux.log, is created on the system drive. To locate the log file go to: %SystemDrive%\uxlog\ux.log The command-line syntax for PackageForTheWeb firmware update package is: Package.exe [-s] [-a [-s] | [-r] | [-c] | [-x directory] | [-xd] | [-w] | [-?] ] [-s] This command installs the Package-For-The-Web software silently and does not prompt if files are to be over-written in the %temp% directory. [-a] This command passes all subsequent commands to the PFTW software to install the update package. [-s] This command runs a silent and unattended update. For firmware updates, the update is scheduled to run on the next reboot. An immediate reboot can be forced with the -r option. [-r] This command schedules the update and reboot immediately. It can be used with or without the -s command. [-c] This command cancels any scheduled firmware update and records results of this operation in the log file. Only one firmware package can be scheduled at a time, if a firmware update needs to be applied instead of the currently scheduled firmware update package, cancel the current (run with the -c option on any firmware package) package. Then, run the applicable firmware package. [-x directory] This command is used with firmware updates to extract the update to the directory named directory. The PackageForTheWeb executable extracts itself to a subdirectory in the %TEMP% directory, a relative directory will be relative to that location. You must specify an absolute directory if you do not want to use the default directory. [-xd] This command is used with firmware updates to extract to a floppy diskette. The floppy diskette can then be used to boot from and apply the update. This option is not available for all firmware updates, such as tape drive and hard-disk drive updates. [-w] PowerQuest Virtual Boot Environment requires that there are 2 free sectors on the first track before it can schedule a firmware update. Use this option only if scheduling an update failed because 2 free sectors were not available on the first track. This option clears the non-boot and the non-partition information sectors on the first track. Typically, these sectors are not used. Before clearing the sectors a copy of the complete first track is saved in the %temp% directory from which the update runs. [-?] This command displays information about the command line switches. The command line switches -s, -r -c and -e are unnattended. Other command line options such as display help (-?) might require that you hit any key to continue. If Windows packages are run without any command line options, a GUI is displayed. This GUI offers all of the options that are available using the command line.