IBM x226/Z20 Flash Update Version 1.49 Installation README File CONTENTS ________ 1.0 Overview 2.0 Change History 3.0 Installation and Setup Instructions 4.0 Configuration Information 5.0 Unattended Mode 6.0 Web Sites and Support Phone Number 7.0 Trademarks and Notices 8.0 Disclaimer 1.0 Overview 1.1 This README file contains the latest information about installing the IBM POST/BIOS code. 1.2 Limitations - NA 1.3 Enhancements - NA 1.4 Level of Recomendations and Prerequisites for the Upate: 1.5 Dependencies 2.0 Change History BIOS Version 1.49- Build PME149A - implemented hardware monitor voltage message(Vin3B) - Added oak fan control algorithm for Delta fan - Changed internal FDD default setting to Disable for Oak BIOS Version 1.48- Build PME148A - Add Table of Contents to enhance remote install function BIOS Version 1.46- Build PME146A - Supports IBM USB Optical Wheel Mouse, 06P4069 - implemented error message of 1-bits error BIOS Version 1.43- Build PME143A - Added user help for No Execute Mode mem protection - Added help for C1 enhanced Mode. - Fixed wrong BIOS version in System Summary - Fixed Default Setting of WOL Startup Sequence - Fixed an exclamation mark in on-board ATI Radeon VGA - Added Oak fan control algorithm BIOS Version 1.42 Build PME142A - Fixed SMBIOS information for CPU L2 Cache  BIOS Version 1.41- Build PME141A - Irwindale CPU supported - Fixed system will get 198 error (processor speed mismatch) while two same speed processors installed BIOS Version 1.36- Build PME136A - Fixed system report the incorrect memory size in memory sizing while 512MB x 6 installed - Fixed " Move config bar in BIOS setup menu is slowly" - Added error code to detect CDROM failure - Added Beep code 3-3-2 when GND I2C Data or CLK - Enhanced BIOS boot sequence setup, showing the network-1 when put Intel Pro/100S in PCI slot. - Enhanced BIOS setup to get two MAC address while put the dual port NIC to the system . BIOS Version 1.35- Build PME135A - Fixed three 6M adapters installed issue-system gets 1807 error - Fixed Wake up modem ring function in S5 BIOS Version 1.34- Build PME134A - Added the Available Memory list in BIOS setup. - Add user help to explain HowTO disabled the Administrator Password. - Add user help to explain HowTO disabled the Power-On Password. - Removed the "spare memory enabled" in SMI log. BIOS Version 1.33 - Build PME133A - Enhanced ASF for server/workstation models - Fixed SMBIOS information - Added POST code to detect additional memory failure conditions - Changed floppy drive reporting when not present - Fixed JCMOS1 jumper support BIOS Version 1.30 - Build PME130A - Change Fan 3 from 0 RPM to NA - Fix Wake on LAN problem - Enhanced memory sparing - E0 processor microcode added - Fixed issue with 5 or more SCSI drives BIOS Version 1.28 - Build PME128A - Fix ACPI stress test failures BIOS Version 1.27 - Build PME127A - Initial release 3.0 Installation and Setup Instructions The procedure to update the POST/BIOS is as follows: 3.1 Insert the "IBM POST/BIOS Flash Update" media for the x226/Z20 xSeries system into drive A:. 3.2 Start up or restart your IBM system. 3.3 The system will boot off of the update media and automatically update the system BIOS. 3.4 On the first system boot after updating the BIOS, select the Setup Utility with the F1 key; then, select the "Load Default Settings" option. Select the "Save Settings" option, and hit 'y' to save. Then, select "Exit Setup" to exit the utility, and, finally, accept the displayed 'Y' option under "Save and exit the setup utility?" 3.5 If you are updating from a floppy diskette and wish to save your current BIOS to a file, mofify 'autoexec.bat' to include the backup '/bu' parameter. Current system BIOS will be saved to a file named 'BIOS.BAK'. 4.0 Configuration Information The following instructions can be used to update SMBIOS and VPD information. 4.1 e.g. Machine Type: 84822RU Serial # : KPAM630 UUID : ... 4.2 First boot the system using a DOS diskette. If using the BIOS floppy for bootup, press F5 during bootup when "Starting PC Dos" appears on the screen. 4.3 To generate a uuid automatically, insert the Flash Diskette and type the following command. phlash16 /p /s /exit /mode=1 /UUID flashfil.fls 4.4 To update machine type (DMI system product ID string), insert the Flash Diskette and type the following command. phlash16 /p /s /exit /mode=1 /DPS:-[84822RU]- flashfil.fls 4.5 To update serial number (DMI system serial number string), insert the Flash Diskette and type the following command. phlash16 /p /s /exit /mode=1 /DSS:KPAM630 flashfil.fls 5.0 Unattended Mode 5.1 Steps for unattended mode. 5.1.1 Modify AUTOEXEC.BAT on the Flash Diskette to read: "PHLASH16.EXE /S /MFG flashfil.fls" 5.1.2 Reboot the system with the Flash Diskette in Drive A: 6.0 Web Sites and Support Phone Number 6.1 IBM Support Web Site: http://www.pc.ibm.com/support 6.2 IBM Marketing IntelliStation Web Site: http://www.pc.ibm.com/intellistation 6.3 If you have any questions about this update, or problems applying the update go to the following Help Center World Telephone Numbers URL: http://www.ibm.com/planetwide/. 7.0 Trademarks and Notices THIS DOCUMENT IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND. IBM DISCLAIMS ALL WARRANTIES, WHETHER EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE AND MERCHANTABILITY WITH RESPECT TO THE INFORMATION IN THIS DOCUMENT. BY FURNISHING THIS DOCUMENT, IBM GRANTS NO LICENSES TO ANY PATENTS OR COPYRIGHTS. 8.0 Disclaimer