IBM eServer xSeries BladeCenter Integrated System Management Processor Update Diskette Version 1.09, Build ID: BR8T35A Systems 8678, 8832 CONTENTS ________ 1.0 Overview 2.0 Change History 3.0 Installation and Setup Instructions 4.0 Unattended Mode 5.0 Web Sites and support phone Number 6.0 Trademarks and Notices 7.0 Disclaimer 1.0 Overview ________________________ This diskette will update the Integrated System Management Processor firmware only. It will not affect any device drivers. 1.1 To use this diskette, perform the following steps: a). Make sure BIOS version 1.04 for 8678 or 1.00 for 8832, or later, is installed. b). Insert this diskette into the diskette drive and restart the system. If your system does not boot from the diskette, use POST/BIOS setup to configure the diskette drive as a boot device. Please refer to the Server Library that was included with your system for additional information. c). After your system boots, the main option menu will appear on the screen. The main option menu contains two options. Type the number of the menu item that you want to perform and press Enter. d). When you are finished using the utility, select "Exit" menu item from the main menu and press Enter. e). When prompted, remove the diskette from the diskette drive and press Enter to restart your system. 1.2 Limitations If there is an error in loading the Integrated System Management Processor software, retry loading the software * by repeating the instructions in section 1.1. 1.3 Enhancements 1.4. Level of Recommendations and Prerequisites for the update: - BIOS version 1.04 for 8678 or 1.00 for 8832 or later, must be installed prior to installing this ISMP firmware update. - A full tape backup should be completed and verified prior to running this, or any other system upgrade. - RAID configuration should be saved to a diskette: see the "Hardware Maintenance Manual" for more details. 1.5 Dependencies: - none 2.0 Change History ______________________________________ Integrated System Management Version 1.09, BR8T35A - Workaround for Ctrl-Alt-Del, causing BSE management bus hang. Integrated System Management Version 1.08, BR8T34A - improve the CPU temperature monitoring Integrated System Management Version 1.07, BR8T33A - fix for watchdog timer not resetting the system upon expiration Integrated System Management Version 1.06, BR8T32A - add support for PCI Expansion Unit voltage monitoring Integrated System Management Version 1.05, BR8T31A - re-establish SOL session after Management Module is restarted. - add support for CPU IError detection and handling Integrated System Management Version 1.04, BR8T30A - added co-required code for Management Module build BRET56A. Integrated System Management Version 1.03, BR8T29A - SOL support. Corequesite with BRET57A. Integrated System Management Version 1.02, BR8T20A - Flash update from older version may inhibit power on/off until AC cycle. Integrated System Management Version 1.01, BR8T17A - Support for 533 Mhz front side bus systems 8832. Integrated System Management Version 1.00, BR8T13B - Original Release 3.0 Installing and Setup Instructions ______________________________________ To install the firmware on this diskette, perform the following steps: 3.1 Make sure BIOS version 1.04 for 8678 or 1.00 for 8832, or later, is installed. 3.2 Make sure your system is powered down. 3.3 Insert the diskette in the diskette drive. 3.4 Power on your system to boot from diskette drive. If your system does not boot from the diskette, use POST/BIOS setup utility to configure the diskette drive as a boot device. 3.5 From the main option menu, select "Update System Management Processor". 3.6 When the update completes, remove the diskette from the drive and press Enter to restart the system. 4.0 Unattended Mode _______________________ This update utility does not support unattended installations but there are other ways to incorporate unattended installations of this code. Check 'Advanced users' section immediately below. Check the UpdateXpress CD for availability of unattended installs of this firmware. (The UpdateXpress CD is downloadable from http://www.ibm.com (use the search function to find " UpdateXpress"). 4.1 Advanced users: The contents of this diskette can be used to support unattended installations. Note: Using this utility in an unattended mode will unconditionally flash the server with the firmware from this update. The server will be flashed regardless of whether the currently installed firmware is older or newer than the firmware on this update. To perform an unattended installation, copy flash2.exe and all of the .BIN files from this diskette to a single directory on your drive. Boot the server to DOS and change the directory to the directory where you have copied these files. At the DOS prompt type: flash2 /u /e 5.0 WEB Sites and Support Phone Number __________________________________________ 5.1 IBM Support Web Site: http://www.pc.ibm.com/support 5.2 IBM eserver xSeries Web Site: http://www.ibm.com/eserver/xseries 5.3 If you have any questions about this update, or problems applying the update, go to the following Help Center World Telephone Numbers and URL: http://www.pc.ibm.com/qtechinfo/YAST-3P2QYL.html. 6.0. TradeMarks and Notices ______________________________ 6.1 The following terms are trademarks of the IBM Corporation in the United States, or other countries or both: * IBM * Netfinity * Netfinity Manager * Advanced System Management Other company, product, and service names may be trademarks or service marks of others. 7.0. Disclaimer __________________ 7.1 THIS DOCUMENT IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND. IBM DISCLAIMS ALL WARRANTIES, WHETHER EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE AND MERCHANTABILITY WITH RESPECT TO THE INFORMATION IN THIS DOCUMENT. BY FURNISHING THIS DOCUMENT, IBM GRANTS NO LICENSES TO ANY PATENTS OR COPYRIGHTS. 7.2 Note to Government users: Note to U.S. Government users-- Documentation related to restricted rights-- Use, duplication and disclosure is subject to restrictions set forth in GSA ADP Schedule Contract with IBM Corporation. Appendix A: Package Specific Installation Instruction This update is packaged as a self extracting shell script. To update your system, just execute the package with the appropriate options. You must be logged on as root, and the package must be run from an ext2/ext3 filesystem. Usage is as follows: packagename.sh [-?] | [-r] | [-s] | [-xd [device]] | [-x dirname] | [-w] -? Shows the command line help -r Install the package and reboot immediately -s Silent/unattented install -xd [device] Extracts contents to floppy disk(s) If device is not specified, floppy device /dev/fd0 is taken as the default. -x dirname Extracts contents to directory specified -w Save track0 to track01.sav and wipe boot sector (assumes -r) UpdateXpress packages use a portion of track0 of the first logical hard drive to store boot information for the virtual floppy environment. Normally, the only data contained on this track is the master boot record (MBR). Occasionally, updates will fail if there is no room to store the boot information on track0. If the update fails, execute the package with the -s -w options. This will erase track0 of the hard drive while preserving the MBR; install the virtual floppy on the drive, and then reboot the system to perform the update. The data contained in track0 is backed up in a file named track0.sav Please Note: The package update for Linux ONLY supports ext2/ext3 filesystems!