IBM eserver xSeries 365 Remote Supervisor Adapter II Update for Linux Systems 8861 and 8862 Version 1.06, Build ID: RDE830B, Revision 16 CONTENTS ________ 1.0 Overview 2.0 Change History 3.0 Installation and Setup Instructions 4.0 Unattended Mode 5.0 Web Sites and support phone Number 6.0 Trademarks and Notices 7.0 Disclaimer 1.0 Overview ________________________ 1.1 This will update the IBM Remote Supervisor Adapter II software only. It will not affect any device drivers. 1.2 Limitations If there is an error in loading the IBM Remote Supervisor Adapter II software, retry loading the software by repeating the instructions in section 3.0. 1.3 Enhancements - none 1.4. Level of Recommendations and Prerequisites for the update: - Multi-lun support is needed in order to mount more then one remote drive simultaneously. The linux kernel 2.4.20 and later have the appropriate multi-lun support, however this support needs to be enabled at kernel build time. Currently, only the SLES 8.0 SP3 distribution has multi-Lun support available and enabled. RedHat AS 3.0 has a 2.4.21 kernel, but does not have multi-lun support enabled by default. 1.5 Dependencies: - none 2.0 Change History ________________________ IBM Remote Supervisor Adapter II Update Version 1.06, RDE830B - Corrected a problem where the server could become non-responsive 76 days after the Remote Supervisor Adapter II has been reset. - Added DNS support for Lightweight Directory Access Protocol - Enhanced the command line interface - Corrected a problem that would cause the Windows flash utility, wflash, to post an Error Code 8 when flashing under Windows Server 2003. - Corrected a problem that would cause the Linux flash utility, lflash, to post an errorcode = 2 message when flashing. IBM Remote Supervisor Adapter II Update Version 1.05, RDE826A - Corrected a special situation where the time/date was saved incorrectedly. IBM Remote Supervisor Adapter II Update Version 1.04, RDE823B - Corrected a situation where the Event Log LED was lit for no apparent reason. - Send a Recovery Event after recovering from a VRM fault. - Assign RXE-100 events to the RSE-100 instead of to the server. IBM Remote Supervisor Adapter II Update Version 1.03, RDE823A - Fixed Alert LED blinking after remind condition clears and Power Supply Thermal Warning not turn LEDs On. IBM Remote Supervisor Adapter II Update Version 1.02, RDE821A - Fixed problems with IBM Director support reading server attributes. Fixed problems in handling Power Alerts. IBM Remote Supervisor Adapter II Update Version 1.01, RDE820A - Fixed problem causing system to reset when flashing to version 1.00 from the web. IBM Remote Supervisor Adapter II Update Version 1.00, RDE819A - First release 3.0 Installing and Setup Instructions ______________________________________ This utility will update the IBM Remote Supervisor Adapter II software under the Linux Operating System. It requires the installation of the correct Remote Supervisor Adapter II for Linux device driver. 3.1 Performing this code update (command line) ________________________________________________ - Run the "IBM xSeries 365 Linux Remote Supervisor Adapter II Update" from a command line with the "-s" parameter. "./.sh -s" where .sh is the downloaded update. NOTE: The following message is shown on RedHat Enterprise Linux 3.0 and other distributions that do not install the compatibility libstdc++ library. ./lflash: error while loading shared libraries: libstdc++-libc6.1-1.so.2: cannot open shared object file: No such file or directory. If the above message is shown, install the compat-libstdc++*.rpm that was included on the distribution media. 3.2 Extracting the Linux update files (command line) __________________________________________________ - Run the "IBM xSeries 365 Linux Remote Supervisor Adapter II Update" with the following command line: "./.sh -x " where .sh is the downloaded update and is the path to which the Linux update files will be extracted. - The files extracted are all the files that are necessary to perform a RSAII firmware update under Linux. Run "./lflash -r" from a command line to update RSAII firmware. 4.0 Unattended Mode ________________________ Extracting the Linux update files (command line) __________________________________________________ - Run the "IBM xSeries 365 Linux Remote Supervisor Adapter II Update" with the following command line: "./.sh -x " where .sh is the downloaded update and is the path to which the Linux update files will be extracted. - The files extracted are all the files that are necessary to perform a RSAII firmware update under Linux. Run "./lflash -r" from a command line to update RSAII firmware. 5.0 WEB Sites and Support Phone Number _________________________________________ 5.1 IBM Support Web Site: http://www.pc.ibm.com/support 5.2 IBM eserver xSeries Web Site: http://www.ibm.com/eserver/xseries 5.3 If you have any questions about this update, or problems applying the update, go to the following Help Center World Telephone Numbers and URL: http://www.pc.ibm.com/qtechinfo/YAST-3P2QYL.html. 6.0. TradeMarks and Notices ______________________________ 6.1 The following terms are trademarks of the IBM Corporation in the United States, or other countries or both: * IBM * Advanced System Management Other company, product, and service names may be trademarks or service marks of others. 7.0. Disclaimer __________________ 7.1 THIS DOCUMENT IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND. IBM DISCLAIMS ALL WARRANTIES, WHETHER EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE AND MERCHANTABILITY WITH RESPECT TO THE INFORMATION IN THIS DOCUMENT. BY FURNISHING THIS DOCUMENT, IBM GRANTS NO LICENSES TO ANY PATENTS OR COPYRIGHTS. 7.2 Note to Government users: Note to U.S. Government users-- Documentation related to restricted rights-- Use, duplication and disclosure is subject to restrictions set forth in GSA ADP Schedule Contract with IBM Corporation.