IBM eserver xSeries 445 Remote Supervisor Adapter II Update for Linux System 8670 Version 1.02, Build ID: REE820A, Revision 16 CONTENTS ________ 1.0 Overview 2.0 Change History 3.0 Installation and Setup Instructions 4.0 Unattended Mode 5.0 Web Sites and support phone Number 6.0 Trademarks and Notices 7.0 Disclaimer 1.0 Overview ________________________ 1.1 This will update the IBM Remote Supervisor Adapter II software only. It will not affect any device drivers. 1.2 Limitations SSL is a commonly used security technology that uses encryption to provide secure TCP/IP communication. In order to comply with regulations regarding the export of products that contain cryptography, the IBM Remote Supervisor Adapter II is shipped without SSL support. In order to install SSL, the installation key file must be obtained and loaded into the Remote Supervisor Adapter II via the web interface. Once the file is loaded, SSL is installed and can be enabled or disabled as desired. If there is an error in loading the IBM Remote Supervisor Adapter II software, retry loading the software by repeating the instructions in section 3.0. 1.3 Enhancements - none 1.4. Level of Recommendations and Prerequisites for the update: - Multi-lun support is needed in order to mount more then one remote drive simultaneously. The linux kernel 2.4.20 and later have the appropriate multi-lun support, however this support needs to be enabled at kernel build time. Currently, only the SLES 8.0 SP3 distribution has multi-Lun support available and enabled. RedHat AS 3.0 has a 2.4.21 kernel, but does not have multi-lun support enabled by default. 1.5 Dependencies: - BIOS version 1.10 or greater is required to support the IBM Remote Supervisor Adapter II. 2.0 Change History ________________________ IBM Remote Supervisor Adapter II Update Version 1.02, REE820A - Added SSH support - Added DNS support for Lightweight Directory Access Protocol - Enhanced the command line interface - Corrected problem where server is non-responsive 76 days after reset. - Fixed problem with clearing Daylight Savings Time (DST) mode across multinode systems. - Corrected problems with lflash and wflash firmware update utilities. - Fixed problem where user permissions could not be set from the web interface. IBM Remote Supervisor Adapter II Update Version 1.01, REE816A - Fixed problem where RXE-100 events were not sent correctly. - Corrected Monitor log event selection button to work properly. - Fixed problem with firmware updates to RXE-100 expansion. - Corrected Blue Locator LED state during normal OS operation. - Corrected UUID sent to Director from RXE-100 expansion events. - Added DNS support for LDAP. - Fixed problem with daylight savings time not working with CLI. IBM Remote Supervisor Adapter II Update Version 1.00, REE811A - First release 3.0 Installing and Setup Instructions ______________________________________ This utility will update the IBM Remote Supervisor Adapter II software under the Linux Operating System. It requires the installation of the correct Remote Supervisor Adapter II for Linux device driver. 3.1 Performing this code update (command line) ________________________________________________ - Run the "IBM xSeries 445 Linux Remote Supervisor Adapter II Update" from a command line with the "-s" parameter. "./.sh -s" where .sh is the downloaded update. NOTE: The following message is shown on RedHat Enterprise Linux 3.0 and other distributions that do not install the compatibility libstdc++ library. ./lflash: error while loading shared libraries: libstdc++-libc6.1-1.so.2: cannot open shared object file: No such file or directory. If the above message is shown, install the compat-libstdc++*.rpm that was included on the distribution media. 3.2 Extracting the Linux update files (command line) __________________________________________________ - Run the "IBM xSeries 445 Linux Remote Supervisor Adapter II Update" with the following command line: "./.sh -x " where .sh is the downloaded update and is the path to which the Linux update files will be extracted. - The files extracted are all the files that are necessary to perform a RSAII firmware update under Linux. Run "./lflash -r" from a command line to update RSAII firmware. 3.3 SSL Installation ______________________ 3.3.1 Begin a web interface session with the selected Remote Supervisor Adapter II. (See the Remote Supervisor Adapter II Installation and User's Guide for more information on using the Remote Supervisor Adapter II web interface.) 3.3.2 Click on Security in the navigation panel. 3.3.3 You are notified that SSL is not installed if the key file has not been loaded previously. Download the key file to a location on your computer, and then specify the location of the file as prompted on the Security page of the web interface. 4.0 Unattended Mode ________________________ Extracting the Linux update files (command line) __________________________________________________ - Run the "IBM xSeries 445 Linux Remote Supervisor Adapter II Update" with the following command line: "./.sh -x " where .sh is the downloaded update and is the path to which the Linux update files will be extracted. - The files extracted are all the files that are necessary to perform a RSAII firmware update under Linux. Run "./lflash -r" from a command line to update RSAII firmware. 5.0 WEB Sites and Support Phone Number _________________________________________ 5.1 IBM Support Web Site: http://www.pc.ibm.com/support 5.2 IBM eserver xSeries Web Site: http://www.ibm.com/eserver/xseries 5.3 If you have any questions about this update, or problems applying the update, go to the following Help Center World Telephone Numbers and URL: http://www.pc.ibm.com/qtechinfo/YAST-3P2QYL.html. 6.0. TradeMarks and Notices ______________________________ 6.1 The following terms are trademarks of the IBM Corporation in the United States, or other countries or both: * IBM * Netfinity * Netfinity Manager * Advanced System Management Other company, product, and service names may be trademarks or service marks of others. 7.0. Disclaimer __________________ 7.1 THIS DOCUMENT IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND. IBM DISCLAIMS ALL WARRANTIES, WHETHER EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE AND MERCHANTABILITY WITH RESPECT TO THE INFORMATION IN THIS DOCUMENT. BY FURNISHING THIS DOCUMENT, IBM GRANTS NO LICENSES TO ANY PATENTS OR COPYRIGHTS. 7.2 Note to Government users: Note to U.S. Government users-- Documentation related to restricted rights-- Use, duplication and disclosure is subject to restrictions set forth in GSA ADP Schedule Contract with IBM Corporation.