IBM eServer BladeCenter HS40 Firmware Flash Disk
                Version 1.17, Build ID: BRMK17A  
           Installation README File


System Supported: 8839

CONTENTS
________

       1.0   Overview
       2.0   Change History
       3.0   Installation and Setup Instructions
       4.0   Configuration Information
       5.0   Web Sites and Support Phone Number
       6.0   Trademarks and Notices
       7.0   Disclaimer

       1.0   Overview

              1.1  This README file contains the latest information about
                   installing the IBM eServer BladeCenter HS40 Firmware.

              1.2  Limitations - NA

              1.3  Enhancements - NA

              1.4  Level of Recommendations and Prerequisites for the Update:

                -  This update is recommended. 
                
              1.5  Dependencies


        2.0   Change History
             Version 1.11 - March 19, 2004 
             ----------------------
              - Initial release
	      
		
        3.0   Installation and Setup Instructions

              The procedure to update the BMC is as follows:

	      3.1 Boot or insert the BMC firmware update diskette into floopy drive

	      3.2 Recommended user copy LCREFLSH.BAT, FWPIAUPD.EXE, FRUSDR.EXE, BRMK17A.HEX and
	        *.SDR file from BMC firmware diskette onto hard drive (optional, but highly 
		recommended as flash times are considerably longer executing from floppy)

	      3.3 Type LCREFFLSH.BAT. Hit 'Enter' 
  
  	      Note: If there are problems, check the boot block jumper (J5G1). Must be on pins 1 & 2


        3.10 Instructions for updating BMC if operational code becomes corrupted
		
	      3.11 Remove HS40 blade	
	      3.11 Move switch BMC_Force_Update (S6H1, bit 5) to On.
   	      3.12 If updating BMC boot code, ensure Write Protect jumper (J5G1) connects pins 1 & 2
   	      3.13 Place HS40 blade in chassis. It will automatically power up and begin 
      		   booting.  Correct KVM and CD selection will automatically occur.
   	      3.14 In DOS run FWPIAUPD 
   	      3.15 Remove HS40 blade
   	      3.16 Move switch BMC_Force_Update back to Off
	      

          
              
       4.0  Configuration Information

       

       5.0  Web Sites and Support Phone Number

              5.1  IBM Support Web Site:
                   http://www.pc.ibm.com/support

              5.2  IBM Marketing Web Site:
                   http://www.pc.ibm.com/ww/eserver/xseries/

              5.3  If you have any questions about this update, or problems
                   applying the update go to the following Help Center World
                   Telephone Numbers URL:
                   http://www.pc.ibm.com/qtechinfo/YAST-3P2QLY.html.


       6.0  Trademarks and Notices
       
              6.1 IBM and the e(logo) are registered trademarks of 
                  International Business Machines Corporation.
                  
              6.2  U.S. Government Users Restricted Rights - Use, duplication
                   or disclosure restricted by GSA ADP Schedule Contract with
                   IBM Corporation.  IBM web site pages may contain other
                   proprietary notices and copyright information which should
                   be observed.
                   
       

        7.0  Disclaimer

             THIS DOCUMENT IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY
             KIND. IBM DISCLAIMS ALL WARRANTIES, WHETHER EXPRESS OR
             IMPLIED, INCLUDING WITHOUT LIMITATION, THE IMPLIED
             WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE AND
             MERCHANTABILITY WITH RESPECT TO THE INFORMATION IN THIS
             DOCUMENT. BY FURNISHING THIS DOCUMENT, IBM GRANTS NO LICENSES
             TO ANY PATENTS OR COPYRIGHTS.