IBM eserver xSeries 235 Remote Supervisor Adapter II Update System 8671 Version 1.04, Build ID: GRE831A, Revision 16 CONTENTS ________ 1.0 Overview 2.0 Change History 3.0 Installation and Setup Instructions 4.0 Unattended Mode 5.0 Web Sites and support phone Number 6.0 Trademarks and Notices 7.0 Disclaimer 1.0 Overview ________________________ 1.1 This will update the IBM Remote Supervisor Adapter II software only. It will not affect any device drivers. 1.2 Limitations SSL is a commonly used security technology that uses encryption to provide secure TCP/IP communication. In order to comply with regulations regarding the export of products that contain cryptography, the IBM Remote Supervisor Adapter II is shipped without SSL support. In order to install SSL, the installation key file must be obtained and loaded into the Remote Supervisor Adapter II via the web interface. Once the file is loaded, SSL is installed and can be enabled or disabled as desired. If there is an error in loading the IBM Remote Supervisor Adapter II software, retry loading the software by repeating the instructions in section 3.0. 1.3 Enhancements - none 1.4. Level of Recommendations and Prerequisites for the update: - Multi-lun support is needed in order to mount more then one remote drive simultaneously. The linux kernel 2.4.20 and later have the appropriate multi-lun support, however this support needs to be enabled at kernel build time. Currently, only the SLES 8.0 SP3 distribution has multi-Lun support available and enabled. RedHat AS 3.0 has a 2.4.21 kernel, but does not have multi-lun support enabled by default. 1.5 Dependencies: - none 2.0 Change History ________________________ IBM Remote Supervisor Adapter II Update Version 1.04, GRE831A - Restore Network Protocol Settings when flashing from earlier firmware levels to this one. IBM Remote Supervisor Adapter II Update Version 1.03, GRE830A - Added LDAP security fixes - Changed the remote disk port number from 4444 to 1044 - Added to readme that Red Hat Linux does not support multi-lun USB functionality - Corrected an issue where a connection could not be made via ASM interconnect when SSL is enabled - Corrected a problem where remote recipient data was not restored properly using the configuration restore utility - Removed SSH ports assignment using SNMP - Changed a power nonredundant state to a warning from an informational alert - Implemented an event log entry to notify in a case of CPU/VRM mismatch - Disabled a command which shows non-pertinent CPU/Memory configuration - Fixed a problem where the event log entries failed to show after using severity filter - Fixed a problem with remote OS installation where mouse cursor is lost - Corrected a problem with rebooting the ASM corrupting settings - Fixed an issue where the Remote control screen did not close - Fixed a problem where video was lost after cancelling remote disk image - Stopped a USB memory device from mounting as a CD ROM drive - Fixed a problem with the ASM not detecting an analog modem connected to the serial port - Removed the dialback command from the supported command list - Fixed a problem with remote graphics over a PPP connection - Fixed a problem that caused the ASM to reset when the Security link on the Web interface was clicked - Fixed a problem where the Windows blue screen capture would fail - Improved the recovery procedure for an ASM interconnect bus hang - Added support for Lightweight Directory Access Protocol - Added support for the Blue Identification LED - Added Remote Disk Multi Drive Support - Added Serial Console Redirection capability - Added support for the Belgian keyboard - Corrected an ethernet connection problem - Fixed the save and restoration of the ISMP gateway setting IBM Remote Supervisor Adapter II Update Version 1.02, GRE824A - Corrected the remote disk feature which would not work if it was run with a Japanese user name - Fixed a condition where alerts would not be generated after the system recovered from a CPU over temperature or system over voltage condition - Added SNMP command support - Added support for French, Italian, German, Spanish and UK keyboards IBM Remote Supervisor Adapter II Update Version 1.01, GRE823A - Provided the numeric pager alerts with different codes to distinguish faults from recoveries. - Corrected the firmware to recognize recoveries from ISMP detected faults on other systems connected via the ASM interconnect. IBM Remote Supervisor Adapter II Update Version 1.00, GRE819A - First release 3.0 Installing and Setup Instructions ______________________________________ To install this update, perform the following steps: a). Open a Web browser. In the address or URL field, type the IP address or host name of the Remote Supervisor Adapter II to which you want to connect. The Enter Network Password window opens. Note: The Remote Supervisor Adapter II defaults to DHCP. If a DHCP host is unavailable, the Remote Supervisor Adapter II assigns a static IP address of 192.168.70.125. b). Type your user name and password in the Enter Network Password window. If you are using the IBM Remote Supervisor Adapter II for the first time, you can obtain your user name and password from your system administrator. All login attempts are documented in the event log. A welcome page opens in your browser. Note: The Remote Supervisor Adapter II is set initially with a user name of USERID and password of PASSW0RD (with a zero, not an O). This user has read/write access. Change this default password during your initial configuration for enhanced security. c). Select a timeout value, in minutes, in the field provided. If your browser is inactive for that number of minutes, the Remote Supervisor Adapter II logs you off the Web interface. d). Click Continue to start the session. The browser opens the System Health page, which gives you a quick view of the system status. e). In the navigation frame, click Firmware Update under Tasks, then click Browse. f). Navigate to the PKT file you want to update. Note: There are two packet files that can be updated: RAETBRUS.PKT RAETMNUS.PKT Repeat steps 3e through 3k for each packet. The packets should be flashed in the order listed above. g). Click Open. The file (including the full path) appears in the box beside Browse. h). To begin the update process, click Update. A progress indicator opens as the file is transferred to temporary storage on the Remote Supervisor Adapter II. A confirmation page opens when the file transfer is completed. i). Verify that the PKT file shown on the Confirm Firmware Update page is what you intend to update. If not, click the Cancel button. j). To complete the update process, click Continue. A progress indicator opens as the firmware on the Remote Supervisor Adapter II is flashed. A confirmation page opens to verify that the update was successful. k). Repeat steps 3e through 3k for each packet. l). After receiving a confirmation that the update process is complete, click the option "Restart ASM" and click the Restart button. Click OK to confirm that you want to restart the Remote Supervisor Adapter II. NOTE: Restarting the Remote Supervisor Adapter II will disconnect your current session. m). Click OK to close the current browser window. n). To log into the Remote Supervisor Adapter II again, open your browser and follow the regular login process. Note: To cancel this process at any point, click Cancel. 3.1 SSL Installation ______________________ 3.1.1 Begin a web interface session with the selected Remote Supervisor Adapter II. (See the Remote Supervisor Adapter II Installation and User's Guide for more information on using the Remote Supervisor Adapter II web interface.) 3.1.2 Click on Security in the navigation panel. 3.1.3 You are notified that SSL is not installed if the key file has not been loaded previously. Download the key file to a location on your computer, and then specify the location of the file as prompted on the Security page of the web interface. 4.0 Unattended Mode ________________________ This update does not support unattended installation. 5.0 WEB Sites and Support Phone Number _________________________________________ 5.1 IBM Support Web Site: http://www.pc.ibm.com/support 5.2 IBM eserver xSeries Web Site: http://www.ibm.com/eserver/xseries 5.3 If you have any questions about this update, or problems applying the update, go to the following Help Center World Telephone Numbers and URL: http://www.pc.ibm.com/qtechinfo/YAST-3P2QYL.html. 6.0. TradeMarks and Notices ______________________________ 6.1 The following terms are trademarks of the IBM Corporation in the United States, or other countries or both: * IBM * Netfinity * Netfinity Manager * Advanced System Management Other company, product, and service names may be trademarks or service marks of others. 7.0. Disclaimer __________________ 7.1 THIS DOCUMENT IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND. IBM DISCLAIMS ALL WARRANTIES, WHETHER EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE AND MERCHANTABILITY WITH RESPECT TO THE INFORMATION IN THIS DOCUMENT. BY FURNISHING THIS DOCUMENT, IBM GRANTS NO LICENSES TO ANY PATENTS OR COPYRIGHTS. 7.2 Note to Government users: Note to U.S. Government users-- Documentation related to restricted rights-- Use, duplication and disclosure is subject to restrictions set forth in GSA ADP Schedule Contract with IBM Corporation.