IBM eserver xSeries 305 Flash Update Diskette Version 1.46A Installation README File CONTENTS ________ 1.0 Overview 2.0 Change History 3.0 Installation and Setup Instructions 4.0 Configuration Information 5.0 Unattended Mode 6.0 Web Sites and Support Phone Number 7.0 Disclaimer 1.0 Overview 1.1 This README file contains the latest information about installing the IBM eserver xSeries 305 POST/BIOS code. 1.2 Limitations - NA 1.3 Enhancements - NA 1.4 Level of Recomendations and Prerequisites for the Upate: 1.5 Dependencies 2.0 Change History BIOS Version 1.46A - Add the Hyper-Threading function. Fix the SuSe Power Management issue. BIOS Version 1.45A - Support Console Redirection. SUSE 8.0 install from USB CD-ROM. BIOS Version 1.44A - Update the firmware for celeron CPU BIOS Version 1.43A - Enable USB Legacy during POST. BIOS Version 1.42A - Change the Super I/O resume mode from 11 to 10. BIOS Version 1.41A - Solve the Windows 95 JA himem.sys will not load issue. BIOS Version 1.40A - Change the memory count display to "??? KBInstall Memory". BIOS Version 1.38A - Solve the USB legacy issue. BIOS Version 1.36A - Added individual memory DIMM enable feature Fixed USB mouse issue BIOS Version 1.33A - Added support for latest Intel processors BIOS Version 1.32A - Added support for RSA Fixed Boot Block recovery issue BIOS Version 1.27A - Initial BIOS release 3.0 Installation and Setup Instructions *Note: If installing from an update package, see additional instructions, in Appendix A. The procedure to update the POST/BIOS is as follows: 3.1 Insert the "IBM eserver xSeries 305 POST/BIOS Flash Diskette" into drive A. 3.2 Start up or restart your IBM system. 3.3 The system will boot off of the diskette. 3.4 You will then be asked if you would like to save the current code to a diskette. If you select 'Y', you need to name the file to be saved. The file will be saved on the diskette. If you select 'N', the utility will continue to the next step. 3.5 At this point, you will be asked if you would like to continue the POST/BIOS flash update. If you select 'Y', the system will update the flash ROM with the new code. When this is complete the system will automatically restart. 3.6 On the first system boot, after updating the BIOS, select the Setup Utility with the F1 key; then, select the "Load Optimized Defaults" option. Select the "Save & Exit Setup" option, and, finally, accept the displayed "Y" option under "Save to CMOS and Exit (Y/N) ? Select Y. 4.0 Configuration Information 5.0 Unattended Mode 5.1 Steps for unattended mode. 5.1.1 Modify AUTOEXEC.BAT on the Flash Diskette to read: "FLASH2.EXE /i:(filename) /u /r" 5.1.2 Reboot the system with the Flash Diskette in Drive A: 6.0 Web Sites and Support Phone Number 6.1 IBM Support Web Site: http://www.pc.ibm.com/support 6.2 IBM Marketing Netfinity Web Site: http://www.pc.ibm.com/netfinity 6.3 IBM Marketing Intellistation Web Site: http://www.pc.ibm.com/intellistation 6.4 If you have any questions about this update, or problems applying the update go to the following Help Center World Telephone Numbers URL: http://www.pc.ibm.com/qtechinfo/YAST-3P2QLY.html. 7.0 Disclaimer THIS DOCUMENT IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND. IBM DISCLAIMS ALL WARRANTIES, WHETHER EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE AND MERCHANTABILITY WITH RESPECT TO THE INFORMATION IN THIS DOCUMENT. BY FURNISHING THIS DOCUMENT, IBM GRANTS NO LICENSES TO ANY PATENTS OR COPYRIGHTS. Appendix A: Package Specific Installation Instruction This update is packaged as a self-extracting Package for the web (PFW). To unpack, this update requires that your TEMP environment variable be set to a path with read/write access. You must be logged in as an administrator. The command-line syntax for Package-For-The-Web Firmware update package is: Package.exe [-s] [-a [-s] | [-r] | [-c] | [-x directory] | [-xd] | [-w] | [-?] ] [-s] This initial -s tells the Package-For-The-Web software to install silently and will not prompt if files need to be over-written in the %temp% directory. [-a] Tells the Package-For-The-Web software to pass all subsequent commands to the install package (i.e. the update). [-s] The second -s option indicates to run the update silently and unattended. For firmware updates the update is scheduled to run on the next reboot. An immediate reboot can be forced with the -r option. [-r] Schedule the update (can be used with or without the -s option, either way it has the same meaning) and reboot immediately. [-c] Cancel any scheduled firmware update and record results of this operation in the log file. Only one firmware packages can be scheduled at one time, if a firmware update needs to be applied instead of the currently scheduled firmware update package, the user needs to cancel the current (run with the -c option on any firmware package) package and subsequently run the applicable firmware package. [-x directory] Use with firmware updates to extract the update to directory named directory. Since the Package-For-The-Web extracts itself to subdirectory in the %TEMP% directory, a relative directory will be relative to that location. Normally the user will want to specify an absolute directory. [-xd] Use with firmware updates to extract floppy diskette(s). The floppy diskette(s) can subsequently be used to boot and apply the update in the customary "apply update from floppy diskette" fashion. This option is not available for all firmware updates, such as Tape Drive and Hard Disk updates. [-w] The PowerQuest Virtual Boot Environment requires 2 free sectors on the first track before it can schedule a firmware update. Use this option only if scheduling an update failed because 2 free sectors were not found in the first track. This option will wipe or clear the non boot and the non partition information sectors on the first track. These sectors are normally not used. Before clearing the sectors a copy of the complete first track is saved in the %temp% directory from which the update runs. [-?] Display information about the command line switches. Only the apply-update-silently (-s) option is necessarily unattended, that is the other command line options such as display help (-?) may require the user to "hit any key" to continue. If Windows packages are run without any command line options, a GUI is displayed. This GUI offers all the options available at the command line, except that the -w option is not available.