Patch Name: PHKL_11408 Patch Description: s700 10.20 VM, CPULIMIT, pstat, LVM, PM cumulative patch Creation Date: 97/06/23 Post Date: 97/06/25 Hardware Platforms - OS Releases: s700: 10.20 Products: N/A Filesets: LVM.LVM-KRN OS-Core.CORE-KRN OS-Core.KERN-RUN ProgSupport.C-INC Automatic Reboot?: Yes Status: General Superseded Critical: Yes PHKL_11408: CORRUPTION PHKL_11406: CORRUPTION PHKL_11238: PANIC So far, the panic only appears on MP systems running the latest Informix release. PHKL_11085: CORRUPTION From a customer perspective, EMC Symmetrix disks can appear to lose or corrupt data when rare spurious errors are reported. The data is actually able to be recovered on the disk, and this patch allows LVM to ignore the fact that the block was once "bad" and obtain the good data from the repaired block. PHKL_10932: OTHER HPMC on Emerald-class systems at boot time. PHKL_10757: PANIC PHKL_10675: PANIC CORRUPTION PHKL_10643: PANIC PHKL_10554: PANIC The HPMC/panic that is fixed by this patch has been observed only in rare instances on pre-release hardware. However, the potential exists for similar problems in the field only if PHKL_9151 has been applied. This fix should also provide increased performance for PA-8000 systems. PHKL_10452: PANIC PHKL_10257: PANIC PHKL_10234: PANIC PHKL_9075: PANIC PHKL_8532: CORRUPTION PHKL_8084: ABORT PHKL_7870: PANIC Path Name: /hp-ux_patches/s700/10.X/PHKL_11408 Symptoms: PHKL_11408: Corruption of memory pages on systems with PA-RISC 2.0 cpu. Problem should happen rarely and only under extreme memory stress. PHKL_11406: When using large environments greater than 20 kbytes user applications dump core sometimes, or get bad data. PHKL_11339: A process launched from shell sees (getrlimit) limits set in the shell via ulimit -t but ignores them. When a process forks, the child sees the limits set by the parent via setrlimit but ignores them PHKL_11238: Panic on S800 MP systems using 10.01+ with latest Informix PHKL_11085: On very rare occasions EMC Symmetrix disk drives will report a disk error which causes LVM to mark the block as bad in its bad block directory. The Symmetrix drive can be "repaired" online by EMC support, but the entry in the LVM bad block directory will prevent any further I/O to the affected block. This patch enables a new relocation policy which will prevent entries from being added to the bad block directory. In order to make use of this new relocation policy, a commands patch, PHCO_10826 must also be installed. Also, algorithms within LVM that deal with PVLinks had built in the assumption that NIKE serial numbers were unique. This turned out to not be the case. The only time that the serial numbers need to be unique is in OPS clusters. This patch removes this restriction for all non-OPS cluster environments. PHKL_11006: timer_settime(2) does not set 10ms timer interval properly. The smallest interval can be set is 20ms. PHKL_10932: (4701353078/DSDe436182) Emerald-class (890, T5x0, T600) systems will experience an HPMC at boot when IODC for memory controllers is being accessed. Note: if you are not experiencing this problem now, then your memory controllers are not subject to this problem. (This problem is NOT intermittant.) PHKL_10821: Although users can now exec() programs with up to 2048000 bytes of argument and env strings, sysconfig() _SC_ARG_MAX continues to return 20480 bytes as the maximum length of all arguments and env strings. PHKL_10800: audit records contain relative path names which the user has no idea where they are anchored. this fix prepends the cwd to the relative path name yielding a complete absolute path PHKL_10757: Workstation Additional Core Enhancements for HP-UX 10.20 (July 1997). This patch provides additional enhancements to support new HP workstations. The primary change is the addition of a new signal (SIGGFAULT) and virtual memory subsystem changes to support virtual device locking for new VISUALIZE-FX graphics hardware. It also contains two bug fixes: one for the MP PDIR bug (could panic the system) and the other for the pstat_cmd() panic. PHKL_10689: HP-UX didn't log any error when a user process: 1. encounters a swap space shortage 2. exceeds a system resource limitation Processes were terminated but the errors were not recorded on any of the system log files. PHKL_10675: (1) System may panic with "panic: sync not stale" while running lvmerge (merging LVM mirrors). For the panic to occur, an i/o timeout must occur during the lvmerge operation which results in a resync getting scheduled. (2) Potential data corruption if user i/o's encounter errors to the same extents which are being reimaged by lvmerge. (3) Various panics during vg activation(vgchange -a). A bit is cleared in a kernel structure which LVM has already freed. If another kernel subsystem has been allocated the freed memory before the bit is cleared, panics or other strange behaviors may occur. This particular defect was introduced by PHKL_9000. PHKL_10643: System panic with Memory Mapped Files on UFS filesystem. A typical kernel stack trace would show a data page fault panic in hdl_unsetbits() called from async_pagein_comp(). PHKL_10554: PA-8000 performance; fix kernel-assisted branch prediction. Corrects corner case condition that causes an HPMC. The stack trace would point to module flip_comb(). This corner case has only been seen in lab-internal testing, using pre-release hardware. It has not been seen on any customer's system. PHKL_10452: Panic: kernel stack overflow; trace includes lv_end(). PHKL_10316: When ptrace is called from the DDE debugger while the DDE debugger has watchpoints set, the ptrace system call is called to single step the user process. If the ptrace call is handling a user signal and another signal event is pro- cessed before returning to the user process from ptrace, ptrace may incorretly sent the user's save_state program counter to an incorrect value and return EIO to the parent debugger. PHKL_10257: Panic with "vn_rele" with EXEC_MAGIC executable run over NFS PHKL_10234: panic: kernel scheduler interrupt PHKL_10176: The total length (including terminators) of all argv and env strings passed to a newly-EXECed process was 20480 bytes. If a greater length was detected, the exec() failed with E2BIG. PHKL_9919: Timing differences between CPU to large, causes MI Daemon to die frequently (often in less than 15 minutes). PHKL_9529: vgdisplay(1M)/vgextend(1M) show incorrect value for max number of PE per PV. PHKL_9273: On MP systems with several processors, applications which do file locking frequently can perform poorly. The symptoms are a high switch rate (switch rate > syscall rate) and heavy system activity (%sys > 90%). PHKL_9151: This patch includes 3 separate performance enhancements. All are targetted for PA-RISC 8000 processors. 1. Kernel-assisted branch prediction. 2. bl->bll branch stub elimination. 3. Re-positioning perf-critical kernel assembly routines. PHKL_9075: Applications using Memory Mapped Files were performing poorly when mapping thousands of pregions to the same file. The problem would mainly be noticed with shared (MAP_SHARED) and exclusive (MAP_FIXED with address in the process private data space) mappings. This patch is required when using the Object Store database product from ODI. Additionally, this patch provides an enhancement to the mprotect(2) system call: mprotect(2) used to fail protecting non mmap(2)'ed addresses. This patch enables to mprotect(2) data, stack and shared memory segment addresses. Finally, this patch fixes a kernel panic with large buffer cache: kernel panic with a data page fault when attempting to copy data from the last page of the third quadrant. This will only occur on systems with a buffer cache of one gigabyte or larger. The panic message will display the following: isr.ior = 0.bffffffc _____9022: running strings on a raw sar(1) output file can show some printable strings (sar ignores these). (This was not shipped as a separate patch.) PHKL_8999: Without this patch customers are limited to supporting 2 nodes in a shared environment With this patch customers can now use SLVM in a 4 node cluster Alternate links for devices such as the Nike disk array are now supported in a shared environment This change supports a new -t switch for lvchange allowing the administrator the option to limit the time lvm holds i/os to be retried on logical volumes when disks are powerfailed. Without using this option, LVM will hold the i/os as long as there is is one disk where the data resides which may eventually return. Using this option would cause LVM to give up on the powerfailed disk and return i/o errors to the user application using the logical volume. This feature is obviously not to be used indiscriminately. For many High Availability applications, having i/os held in kernel indefinitely is not acceptable. Most customers should not need to use the new switch. PHKL_8716: After call to pstat_getmsg(), all accesses to the message queue pstat_getmsg() was called hang. PHKL_8532: System crash dumps are corrupt and unusable. PHKL_8346: Executables cannot access more than 1.75 GB shared memory PHKL_8084: LVM may return I/O's with errors instead of sending them to an alternate link. This patch also facilitates using "vgreduce -f" for physical volumes which have alternate links; without this patch "vgreduce -f" is not allowed on LVM disks with alternate links. PHKL_7951: Ptrace not allowing writes on PCUX to some f.p regs PHKL_7870: lvreduce(1M) may cause a system panic, if it is used to reduce an lvol which was left inconsistent by a prior LVM operation. lvreduce(1M) could not be used to remove lvols that were somehow corrupted, if it was, the command would cause a system panic. Defect Description: PHKL_11408: One of the kernel macros used for locking pfdats was using the &htbl[] hash list of locks instead of the &htbl2_0[] hash list of locks, causing it think it had locked a pfdat when it hadn't. PHKL_11406: During the final stages of EXEC, the kernel has to relocate the argv and envp pointers to point to the argument and environment strings which reside in the user stack. There was a defect in this reloction code that caused all pointers pointing to locations in the user's stack at offsets of 20K from the base to have bad addresses. PHKL_11339: CPU limit was not being inherited by the child from the parent and hence if cpulimit is set, child ignores it. Also SIGXCPU is not delivered solely depending on the sigmask, but is triggered by arming the timer. When a child is forked, kt->sigmask is copied from parent to the child but if there is a non infinite cpu limit set in the parent, not only does that field needs to be copied to the child process, the timer for the cpulimit must also be armed for the child. PHKL_11238: Random S800 MP system panics when running the latest Informix because of a corner-case MP hole in nanosleep which is seen when nanosleep() is called from within a signal handler. PHKL_11085: On very rare occasions EMC Symmetrix disk drives will report a disk error which causes LVM to mark the block as bad in its bad block directory. The Symmetrix drive can be "repaired" online by EMC support, but the entry in the LVM bad block directory will prevent any further I/O to the affected block. This patch enables a new relocation policy which will prevent entries from being added to the bad block directory. In order to make use of this new relocation policy, a commands patch, PHCO_10826 must also be installed. Also, algorithms within LVM that deal with PVLinks had built in the assumption that NIKE serial numbers were unique. This turned out to not be the case. The only time that the serial numbers need to be unique is in OPS clusters. This patch removes this restriction for all non-OPS cluster environments. PHKL_11006: A defect in the implementation of timer reload causes the 1 tick (10ms) interval be rounded to 2 ticks (20ms). PHKL_10932: (4701353078/DSDe436182) uiomove accesses memory via load-byte operations to improve performance on PA-8000 systems. Load-byte is not a valid operation for I/O address space, though most I/O cards handle it without problems. Some Emerald-class (890, T5x0, T600) memory controllers do not. We now use load-word for I/O space. PHKL_10821: An earlier patch, (10177, shown without prefix so as not to confuse search engines) expanded the actual space available to execve(), but failed to modify sysconfig() to report the new maximum. This patch corrects that. There is no change to module kern_exec.c (home of execve()) other than a revision roll to ensure its inclusion in this patch. PHKL_10800: current system does not keep track of chdir() calls which alter the current working directory. there is no in kernel ascii record of the current path just the vnode/inode which can not be easily converted to the ascii pathname PHKL_10757: This patch provides additional enhancements to support new HP workstations (See "Symptoms" section for more details). It also contains two bug fixes. One fix is for the MP PDIR bug. On MP systems the system could crash due to a race condition where one processor would attempt to read a translation that was being modified by another processor. The other fix was for a panic that was introduced by a previous patch which expanded the argv/envp buffer from 20480 bytes to 2048000 bytes. pstat_cmd() could get a data segmentation violation due to a defect which would keep looking for a null termination beyond one of the internal buffers, possibly referencing an illegal memory address. PHKL_10689: This patch provide support for logging of errors in memory management related system calls such as brk/sbrk as well as handling error cases during stack growth. Errors are logged on the system console (dmesg) and also in syslog. The variable mman_elog, which defaults to OFF, is used to control the logging. This variable can be set through adb at a customer site to enable error logging. PHKL_10675: LVM resyncs are not held off long enough during lvmerge. If an i/o timeout occurs during reimaging, then a resync is scheduled. Towards the end of lvmerge, there is a window in which the resync is allowed to run for a little bit. If the resync gets started on resyncing a stale extent during that interval, and the lvmerge is reimaging the same extent, the panic can occur. User i/o's can encounter errors during lvmerge, but lvmerge wasn't taking these errors into account. There is the potential that extents can be falsely marked fresh during lvmerge if user i/o's occur, resulting in data corruption if those extents are read. During activation (vgchange -a), LVM allocates various pvol structures. A bit is cleared after a structure has been freed. 32 bit systems expect this low-order bit to be zero anyway (aligned addrs), so there is no impact if the freed memory has not yet been allocated to another subsystem before the bit is cleared. However, if the memory has been reallocated during this interval (i.e. on MP systems), various panics and strange behaviors could occur. PHKL_10643: There were two defects in the UFS read-ahead pagein code causing the system to request more read-ahead pages than the system maximum limit. Since the number of requested pages exceeded the allowed maximum, this resulted in overflowing internal arrays, and the system could then panic while using garbled data. First, the book-keeping of the variables tracking the "last read-ahead" and the "expected next fault" was not always done properly. There was a situation where the "expected next fault" could end up exceeding the "last read-ahead", and this resulted in a read-ahead count greater than the system maximum limit. Second, there was a corner case code path using the "last read-ahead" variable before it had been initialized. PHKL_10554: PA-8000 systems with patch PHKL_9151 applied could experience an HPMC if the following were true: an external interrupt occurred while on the gateway page and the IIR in the save-state happened to contain a comb* instruction. Applying this fix will not only prevent this kind of failure, but should also boost performance on PA-8000 systems. PHKL_10452: Defect is quite rare. Kernel stack overflow may result from other causes. This fix reduces frame size of lv_end() from over 600 bytes to under 200 bytes. PHKL_10316: If ptrace() is single stepping an user signal handler and handling a sigcleanup call, and another signal is handled during the return of this system call, the user's PC is overwritten by the single step breakpoint address before returning to the user. One way to reproduce the problem is to use DDE on a program that generates a lot of signals. Signal stepping through the program will eventually cause an internal I/O error. PHKL_10257: The problem fixed was a wrong assumption in add_text which expects the fstore to be the same as the bstore. Because of this assumption the original (and correct) bstore gets trashed when it is overwritten with the fstore after a call to duplicate a region. For an NFS executale with the sticky bit set, the fstore will NOT be the same as the bstore. We know have removed this assumption. PHKL_10234: Running an EXEC_MAGIC program using a stack pointer in the first quadrant could result in a panic: kernel scheduler interrupt. This problem would only be seen on UP systems. PHKL_10176: The internal buffer within the kernel was created with a length of 20480 bytes, with no provision for increasing its size. This patch provides for up to 100 such buffers, with all but the first allocated only if required (that is, if more than 20480 bytes of argv/env information is found). Thus, exec() now supports up to 2048000 bytes of argv/env information. PHKL_9919: Upon synchronization, non-monarch's expect the monarch to be waiting for them to synchronize. If the monarch is not waiting, the synchronization fails, and the offset_correction is set to 0. This happens only on bootup and may not happen every time. This causes times in the KI buffers to vary greatly, and that causes the MI Daemon to crash frequently. The problem is only at boot time, and will not occur later. This means a succesful boot will keep stay good, and a bad boot will stay bad. PHKL_9529: The lv_queryvg() function in ioctl(2) failed to copy the maxpxs field to the returning data structure. This problem was introduced in PHKL_8999. PHKL_9273: The file locking code is protected by a single semaphore (the filesys sema). As the semaphore becomes heavily utilized, starvation prevention code activates which leads to excessive spinning and switching. PHKL_9151: The changes are designed to improve locality of reference within the kernel, thus improving the i-cache hit rate. The "flipper" tool will reduce mis-predicted branches. All will improve the processor efficiency, or CPI rate, when executing kernel code. PHKL_9075: This patch provides two enhancements to Memory Mapped Files: increased performance when using thousands of mappings, and mprotect(2) opened to non-mmap(2) addresses. It also provides a fix for a defect with large buffer cache. The pregions list associated to a shared region was designed as a doubly-linked list thus providing a linear access to pregions in the list. This design was not suited to deal with thousands of pregions and the doubly-linked list was replaced by a skip-list for faster access. Two other changes were required to deliver better performance: the algorithm to check the total virtual address space and the routine to locate the stack pregion were enhanced. Only those addresses returned from a call to mmap(2) could be used for mprotect(2). However there were applications who needed to protect addresses in data, stack or shared memory segments; objects not created via call to mmap(2). So mprotect(2) was opened to allow mprotect'ing on data, stack and shared memory objects. Text is not allowed unless the executable is EXEC_MAGIC. A compiler feature with C language structure copies results in a reference to an untranslated address when copying the last 4 bytes in quadrant 3. This only shows up when the data in the buffer that is being copied includes address 0xbffffffc that is, it is the last full word in quadrant 3. The problem appears as a trap type 15: "data page fault". _____9022: pstat_dynamic() allocates a buffer but fails to initialize it before using it. Buffer ends up containing some garbage. This is a cosmetic defect only; sar ignores the uninitialized spaces. (not shipped as a separate patch). PHKL_8999: Support for SLVM is currently limited to 2 nodes. This patch will allow SLVM to work in a 4 node cluster. Alternate link support has also been added for SLVM so that devices such as the Nike disk array can now be used in a high availability cluster. LVM makes every effort to avoid returning an error to user applications. LVM will hold onto an I/O to retry it later if there is even the smallest hope that the device will return. If a disk simply does not respond and no bad writes made it to the media, LVM will hang onto the i/o as long as the disk does not respond with an indication that there was actually a bad write or read. The patch provides a new feature that allows administrators the option of limiting the time lvm will wait for disks in an logical volume to return, and cause lvm to return i/os with EIO instead of hanging onto them indefinitely. PHKL_8716: pstat_msginfo() calls msgconv() to convert the offset into a message queue pointer. msgconv() was changed to not only do the conversion, but to lock the queue and return a pointer to the queue's lock. pstat_msginfo() had not been changed to take into account msgconv()'s new behavior. PHKL_8532: Intermittent corrupted dumps on PA-RISC2.0 (PA8000) machines on HP-UX 10.20. PHKL_8346: Current executable types cannot access more than 1.75 GB of shared memory. A new executable type is defined which uses the second quadrant of the address space for shared memory rather than process private data thus resulting in 2.75 GB of shared memory. With short pointer addressing on 32-bit PA architecture, each pointer addresses one of four quadrants each of which is 1 GB in size. Current executable types use quadrant 3 and quadrant 4 for shared memory. In user mode, quadrant 1 and quadrant 2 are used for user text and data, respectively. This results in a system wide maximum of 1.75 GB of shared memory (.25 GB in quadrant 4 is set aside for IO). In the new executable type, user data and stack are pushed into quadrant 1 and quad 2 is also used for shared memory. An existing application has to be relinked as the new executable type to avail of this feature. Alternately the application can be linked as an EXEC_MAGIC and the n the executable can be chatr'd to be the new executable type (SHMEM_MAGIC). The related patch for chatr is PHSS_8358. Only the chatr method is currently supported. Please note that this is an interim solution for increased shared memory addressing till 64-bit hp-ux becomes available. There are several limitations: - Only executables that are linked to be the new SHMEM_MAGIC executable type(or chatrd to be so) can avail of this feature. Other executables will continue to see a system wide maximum of 1.75 GB of shared memory. Processes that execute other types of executables will not be able to share the memory in quadrant 2 with a process that is executing the new executable type. - In the new SHMEM_MAGIC type, quadrant 2 is only used for system V shared memory (unlike quadrants 3 and 4 which are also used for shared memory mapped files). - In the new executable type text is mapped at different virtual addresses and so process intensive applications may not benefit. Any increase in performance due to the larger shared memory may be offset by decreases due to TLB inefficiency. Applications that use one process per processor may however benefit. - This will not be supported on future HP implementations of 64-bit architectures (beyond PA 2.0), nor will it need to be as with a 64-bit kernel the size of shared memory supported will be much larger than 2.75 GB. Programs that need more than 1.75 GB of shared memory on these architectures will have to be recompiled for these architectures. - Programs that are compiled as 64-bit executables on any 64-bit HP implementation (including PA 2.0) cannot be marked as SHMEM_MAGIC nor do they need to be as they will already have access to more than 1.75 GB of shared memory. PHKL_8084: Without this patch LVM will not retry failed i/os on alternate links unless the error is one that denotes that the device is offline or powerfailed. Other errors, are not retried on an alternate link and may cause LVM to report the error to users applications. Typically, customers with unmirrored lvols using multiported devices like the HP3232 (Nike) disk array would see the problem when an EIO error is reported to LVM from the underlying device driver due to a device or driver problem. In this situation LVM would report the EIO to user applications without trying any available alternate link. Another problem this patch fixes allows reducing out physical volumes from a volume group when the device is not available and the device has links, formerly devices with links could not be removed if they were not available. PHKL_7951: 32 bit registers were allowed to be modified after 64 bit registers have been modified. PHKL_7870: The problem was that the kernel forced a panic whenever any inconsistency was found during an lvreduce. For example, if a logical extent in an lvol referred to a physical extent that was not allocated, it would cause lvreduce(1M) to panic the system. This occured even when the objective was to remove the offending lvol. This is a very rare occurance. SR: 0000000000 1653096131 1653194977 1653207175 1653211607 4701329433 4701330647 4701334367 4701334698 4701334847 4701335497 4701335935 4701336412 4701339226 4701341362 4701341644 4701345843 4701347922 4701349431 4701350157 4701350975 4701352278 4701353078 4701354274 4701355321 4701358143 5003314633 5003318667 5003323493 5003325506 5003334961 5003341925 5003344630 5003357616 5003359414 5003360024 5003363820 5003366500 Patch Files: /usr/conf/h/audit.h /usr/conf/lib/libhp-ux.a(asm_rv.o) /usr/conf/lib/libhp-ux.a(asm_scall.o) /usr/conf/lib/libhp-ux.a(asm_utl.o) /usr/conf/lib/libhp-ux.a(asm_vm_pdir.o) /usr/conf/lib/libhp-ux.a(bcopy.o) /usr/conf/lib/libhp-ux.a(btlb.o) /usr/conf/lib/libhp-ux.a(bzero.o) /usr/conf/lib/libhp-ux.a(clock.o) /usr/conf/lib/libhp-ux.a(cpd.o) /usr/conf/lib/libhp-ux.a(dump.o) /usr/conf/lib/libhp-ux.a(flipper.o) /usr/conf/lib/libhp-ux.a(hdl_fault.o) /usr/conf/lib/libhp-ux.a(hdl_init.o) /usr/conf/lib/libhp-ux.a(hdl_mprotect.o) /usr/conf/lib/libhp-ux.a(hdl_policy.o) /usr/conf/lib/libhp-ux.a(hdl_trans.o) /usr/conf/lib/libhp-ux.a(init_main.o) /usr/conf/lib/libhp-ux.a(interrupt.o) /usr/conf/lib/libhp-ux.a(kern_exec.o) /usr/conf/lib/libhp-ux.a(kern_fork.o) /usr/conf/lib/libhp-ux.a(kern_kload.o) /usr/conf/lib/libhp-ux.a(kern_mman.o) /usr/conf/lib/libhp-ux.a(kern_sig.o) /usr/conf/lib/libhp-ux.a(lbcopy.o) /usr/conf/lib/libhp-ux.a(lbzero.o) /usr/conf/lib/libhp-ux.a(lv_config.o) /usr/conf/lib/libhp-ux.a(lv_lvm.o) /usr/conf/lib/libhp-ux.a(lw_scall.o) /usr/conf/lib/libhp-ux.a(outlaw.o) /usr/conf/lib/libhp-ux.a(pgcopy.o) /usr/conf/lib/libhp-ux.a(pm_clockint.o) /usr/conf/lib/libhp-ux.a(pm_config.o) /usr/conf/lib/libhp-ux.a(pm_context.o) /usr/conf/lib/libhp-ux.a(pm_core.o) /usr/conf/lib/libhp-ux.a(pm_policy.o) /usr/conf/lib/libhp-ux.a(pm_proc.o) /usr/conf/lib/libhp-ux.a(pm_procdup.o) /usr/conf/lib/libhp-ux.a(pm_ptrace.o) /usr/conf/lib/libhp-ux.a(pm_resource.o) /usr/conf/lib/libhp-ux.a(pm_sendsig.o) /usr/conf/lib/libhp-ux.a(pm_signal.o) /usr/conf/lib/libhp-ux.a(pm_swtch.o) /usr/conf/lib/libhp-ux.a(pm_threads.o) /usr/conf/lib/libhp-ux.a(pm_timers.o) /usr/conf/lib/libhp-ux.a(protection.o) /usr/conf/lib/libhp-ux.a(pstat.o) /usr/conf/lib/libhp-ux.a(resume.o) /usr/conf/lib/libhp-ux.a(sem_alpha.o) /usr/conf/lib/libhp-ux.a(subr_ksleep.o) /usr/conf/lib/libhp-ux.a(subr_timers.o) /usr/conf/lib/libhp-ux.a(sysV_shm.o) /usr/conf/lib/libhp-ux.a(ulbcopy.o) /usr/conf/lib/libhp-ux.a(vfs_vm.o) /usr/conf/lib/libhp-ux.a(vm_machdep.o) /usr/conf/lib/libhp-ux.a(vm_machreg.o) /usr/conf/lib/libhp-ux.a(vm_mmap.o) /usr/conf/lib/libhp-ux.a(vm_pdir1_1.o) /usr/conf/lib/libhp-ux.a(vm_pdir2_0.o) /usr/conf/lib/libhp-ux.a(vm_pregion.o) /usr/conf/lib/libhp-ux.a(vm_region.o) /usr/conf/lib/libhp-ux.a(vm_sched.o) /usr/conf/lib/libhp-ux.a(vm_superpage.o) /usr/conf/lib/libhp-ux.a(vm_text.o) /usr/conf/lib/libhp-ux.a(vm_vas.o) /usr/conf/lib/libhp-ux.a(vm_vhand.o) /usr/conf/lib/liblvm.a(lv_block.o) /usr/conf/lib/liblvm.a(lv_cluster_lock.o) /usr/conf/lib/liblvm.a(lv_defect.o) /usr/conf/lib/liblvm.a(lv_hp.o) /usr/conf/lib/liblvm.a(lv_ioctls.o) /usr/conf/lib/liblvm.a(lv_kdb.o) /usr/conf/lib/liblvm.a(lv_lvsubr.o) /usr/conf/lib/liblvm.a(lv_malloc.o) /usr/conf/lib/liblvm.a(lv_mircons.o) /usr/conf/lib/liblvm.a(lv_pbuf.o) /usr/conf/lib/liblvm.a(lv_phys.o) /usr/conf/lib/liblvm.a(lv_schedule.o) /usr/conf/lib/liblvm.a(lv_spare.o) /usr/conf/lib/liblvm.a(lv_strategy.o) /usr/conf/lib/liblvm.a(lv_stub.o) /usr/conf/lib/liblvm.a(lv_subr.o) /usr/conf/lib/liblvm.a(lv_syscalls.o) /usr/conf/lib/liblvm.a(lv_vgda.o) /usr/conf/lib/liblvm.a(lv_vgsa.o) /usr/conf/lib/liblvm.a(sh_vgsa.o) /usr/conf/lib/liblvm.a(slvm_comm.o) /usr/conf/lib/liblvm.a(slvm_schedule.o) /usr/conf/master.d/core-hpux /usr/conf/space.h.d/core-hpux.h /usr/include/sys/audit.h what(1) Output: /usr/conf/h/audit.h: audit.h $Date: 97/04/21 13:54:38 $ $Revision: 1.10.98.5 $ PATCH_10.20 (PHKL_10800) /usr/conf/lib/libhp-ux.a(asm_rv.o): asm_rv.s $Date: 97/02/28 14:51:08 $ $Revision: 1.57 .98.11 $ PATCH_10.20 (PHKL_10234) /usr/conf/lib/libhp-ux.a(asm_scall.o): asm_scall.s $Date: 96/11/22 10:45:59 $ $Revision: 1 .39.98.6 $ PATCH_10.20 (PHKL_9151) /usr/conf/lib/libhp-ux.a(asm_utl.o): asm_utl.s $Date: 96/11/22 10:49:42 $ $Revision: 1.1 17.98.10 $ PATCH_10.20 (PHKL_9151) /usr/conf/lib/libhp-ux.a(asm_vm_pdir.o): asm_vm_pdir.s $Date: 97/05/02 01:58:51 $ $Revision: 1.2.98.5 $ PATCH_10.20 (PHKL_10757) /usr/conf/lib/libhp-ux.a(bcopy.o): bcopy.s $Date: 96/11/22 10:51:06 $ $Revision: 1.7.9 8.4 $ PATCH_10.20 (PHKL_9151) /usr/conf/lib/libhp-ux.a(btlb.o): btlb.c $Date: 97/05/02 02:00:53 $ $Revision: 1.9. 98.4 $ PATCH_10.20 (PHKL_10757) /usr/conf/lib/libhp-ux.a(bzero.o): bzero.s $Date: 96/11/22 10:52:32 $ $Revision: 1.9.9 8.4 $ PATCH_10.20 (PHKL_9151) /usr/conf/lib/libhp-ux.a(clock.o): clock.c $Date: 97/01/23 16:09:43 $ $Revision: 1.39. 98.4 $ PATCH_10.20 (PHKL_9919) /usr/conf/lib/libhp-ux.a(cpd.o): cpd.c $Date: 96/10/26 09:39:05 $ $Revision: 1.9.98.8 $ PATCH_10.20 (PHKL_8999) /usr/conf/lib/libhp-ux.a(dump.o): dump.c $Date: 96/10/26 09:49:44 $ $Revision: 1.11.98.6 $ PATCH_10.20 (PHKL_8999) /usr/conf/lib/libhp-ux.a(flipper.o): flipper.c $Date: 97/03/31 14:58:19 $ $Revision: 1.3. 98.8 $ PATCH_10.20 (PHKL_10554) /usr/conf/lib/libhp-ux.a(hdl_fault.o): hdl_fault.c $Date: 97/05/02 02:00:56 $ $Revision: 1.13.98.11 $ PATCH_10.20 (PHKL_10757) /usr/conf/lib/libhp-ux.a(hdl_init.o): hdl_init.c $Date: 96/08/26 22:38:17 $ $Revision: 1.9.98.5 $ PATCH_10.20 (PHKL_8346) /usr/conf/lib/libhp-ux.a(hdl_mprotect.o): hdl_mprotect.c $Date: 96/11/20 10:52:46 $ $Revision : 1.4.98.3 $ PATCH_10.20 (PHKL_9075) /usr/conf/lib/libhp-ux.a(hdl_policy.o): hdl_policy.c $Date: 97/05/02 02:00:58 $ $Revision: 1.15.98.11 $ PATCH_10.20 (PHKL_10757) /usr/conf/lib/libhp-ux.a(hdl_trans.o): hdl_trans.c $Date: 96/11/21 16:23:49 $ $Revision: 1.12.98.11 $ PATCH_10.20 (PHKL_9075) /usr/conf/lib/libhp-ux.a(init_main.o): init_main.c $Date: 97/06/17 15:09:59 $ $Revision: 1.120.98.13 $ PATCH_10.20 (PHKL_11406) /usr/conf/lib/libhp-ux.a(interrupt.o): interrupt.s $Date: 97/03/31 13:22:48 $ $Revision: 1 .12.98.10 $ PATCH_10.20 (PHKL_10554) /usr/conf/lib/libhp-ux.a(kern_exec.o): kern_exec.c $Date: 97/06/17 15:50:27 $ $Revision: 1.93.98.22 $ PATCH_10.20 (PHKL_11406) /usr/conf/lib/libhp-ux.a(kern_fork.o): kern_fork.c $Date: 97/05/02 02:02:56 $ $Revision: 1.71.98.18 $ PATCH_10.20 (PHKL_10757) /usr/conf/lib/libhp-ux.a(kern_kload.o): kern_kload.c $Date: 97/05/02 02:02:58 $ $Revision : 1.4.98.5 $ PATCH_10.20 (PHKL_10757) /usr/conf/lib/libhp-ux.a(kern_mman.o): kern_mman.c $Date: 97/04/09 11:33:14 $ $Revision: 1.35.98.5 $ PATCH_10.20 (PHKL_10689) /usr/conf/lib/libhp-ux.a(kern_sig.o): kern_sig.c $Date: 97/05/02 02:03:00 $ $Revision: 1.66.98.4 $ PATCH_10.20 (PHKL_10757) /usr/conf/lib/libhp-ux.a(lbcopy.o): lbcopy.s $Date: 97/05/02 16:44:13 $ $Revision: 1.7. 98.6 $ PATCH_10.20 (PHKL_10932) /usr/conf/lib/libhp-ux.a(lbzero.o): lbzero.s $Date: 96/11/22 10:57:29 $ $Revision: 1.9. 98.4 $ PATCH_10.20 (PHKL_9151) /usr/conf/lib/libhp-ux.a(lv_config.o): lv_config.c $Date: 96/10/25 20:52:33 $ $Revision: 1. 13.98.6 $ PATCH_10.20 (PHKL_8999) /usr/conf/lib/libhp-ux.a(lv_lvm.o): lv_lvm.c $Date: 96/10/25 21:03:34 $ $Revision: 1.3.9 8.2 $ PATCH_10.20 (PHKL_8999) /usr/conf/lib/libhp-ux.a(lw_scall.o): lw_scall.s $Date: 97/05/02 02:01:00 $ $Revision: 1.18.98.7 $ PATCH_10.20 (PHKL_10757) /usr/conf/lib/libhp-ux.a(outlaw.o): outlaw.c $Date: 96/11/22 11:17:11 $ $Revision: 1.2.98.3 $ PATCH_10.20 (PHKL_9151) /usr/conf/lib/libhp-ux.a(pgcopy.o): pgcopy.s $Date: 96/11/22 18:05:02 $ $Revision: 1.7. 98.5 $ PATCH_10.20 (PHKL_9151) /usr/conf/lib/libhp-ux.a(pm_clockint.o): pm_clockint.c $Date: 96/11/22 11:20:15 $ $Revision: 1.7.98.6 $ PATCH_10.20 (PHKL_9151) /usr/conf/lib/libhp-ux.a(pm_config.o): pm_config.c $Date: 97/06/17 15:09:55 $ $Revision: 1. 6.98.8 $ PATCH_10.20 (PHKL_11406) /usr/conf/lib/libhp-ux.a(pm_context.o): pm_context.c $Date: 96/08/26 22:35:25 $ $Revision : 1.3.98.6 $ PATCH_10.20 (PHKL_8346) /usr/conf/lib/libhp-ux.a(pm_core.o): pm_core.c $Date: 97/05/02 02:03:02 $ $Revision: 1 .9.98.9 $ PATCH_10.20 (PHKL_10757) /usr/conf/lib/libhp-ux.a(pm_policy.o): pm_policy.c $Date: 96/11/20 16:35:14 $ $Revision: 1.7.98.7 $ PATCH_10.20 (PHKL_9273) /usr/conf/lib/libhp-ux.a(pm_proc.o): pm_proc.c $Date: 97/06/11 17:26:34 $ $Revision: 1.13 .98.12 $ PATCH_10.20 (PHKL_11339) /usr/conf/lib/libhp-ux.a(pm_procdup.o): pm_procdup.c $Date: 97/05/02 02:03:06 $ $Revision : 1.11.98.13 $ PATCH_10.20 (PHKL_10757) /usr/conf/lib/libhp-ux.a(pm_ptrace.o): pm_ptrace.c $Date: 97/05/02 02:03:08 $ $Revision: 1. 6.98.25 $ PATCH_10.20 (PHKL_10757) /usr/conf/lib/libhp-ux.a(pm_resource.o): pm_resource.c $Date: 97/06/11 17:28:51 $ $Revision: 1.7.98.14 $ PATCH_10.20 (PHKL_11339) /usr/conf/lib/libhp-ux.a(pm_sendsig.o): pm_sendsig.c $Date: 97/05/02 02:01:02 $ $Revision : 1.4.98.12 $ PATCH_10.20 (PHKL_10757) /usr/conf/lib/libhp-ux.a(pm_signal.o): pm_signal.c $Date: 97/05/02 14:45:03 $ $Revision: 1.6.98.16 $ PATCH_10.20 (PHKL_10757) /usr/conf/lib/libhp-ux.a(pm_swtch.o): pm_swtch.c $Date: 97/05/02 02:03:10 $ $Revision: 1.7.98.15 $ PATCH_10.20 (PHKL_10757) /usr/conf/lib/libhp-ux.a(pm_threads.o): pm_threads.c $Date: 97/05/02 02:03:13 $ $Revision : 1.3.98.11 $ PATCH_10.20 (PHKL_10757) /usr/conf/lib/libhp-ux.a(pm_timers.o): pm_timers.c $Date: 97/06/06 09:21:54 $ $Revision: 1 .7.98.7 $ PATCH_10.20 (PHKL_11238) /usr/conf/lib/libhp-ux.a(protection.o): protection.s $Date: 96/11/22 11:00:38 $ $Revision: 1.10.98.4 $ PATCH_10.20 (PHKL_9151) /usr/conf/lib/libhp-ux.a(pstat.o): pstat.c $Date: 97/05/13 16:52:30 $ $Revision: 1.18.9 8.22 $ PATCH_10.20 (PHKL_10757) /usr/conf/lib/libhp-ux.a(resume.o): resume.s $Date: 96/11/22 11:01:44 $ $Revision: 1.11 .98.4 $ PATCH_10.20 (PHKL_9151) /usr/conf/lib/libhp-ux.a(sem_alpha.o): sem_alpha.c $Date: 96/11/20 16:33:04 $ $Revision: 1.11.98.5 $ PATCH_10.20 (PHKL_9273) /usr/conf/lib/libhp-ux.a(subr_ksleep.o): subr_ksleep.c $Date: 97/05/02 02:03:21 $ $Revisio n: 1.1.98.13 $ PATCH_10.20 (PHKL_10757) /usr/conf/lib/libhp-ux.a(subr_timers.o): subr_timers.c $Date: 97/06/11 17:21:12 $ $Revision: 1.8.98.11 $ PATCH_10.20 (PHKL_11339) /usr/conf/lib/libhp-ux.a(sysV_shm.o): sysV_shm.c $Date: 96/11/20 11:01:21 $ $Revision: 1.54.98.5 $ PATCH_10.20 (PHKL_9075) /usr/conf/lib/libhp-ux.a(ulbcopy.o): ulbcopy.s $Date: 97/05/02 17:43:33 $ $Revision: 1.4. 98.8 $ PATCH_10.20 (PHKL_10932) /usr/conf/lib/libhp-ux.a(vfs_vm.o): vfs_vm.c $Date: 97/04/07 13:35:26 $ $Revision: 1.1 7.98.16 $ PATCH_10.20 (PHKL_10643) /usr/conf/lib/libhp-ux.a(vm_machdep.o): vm_machdep.c $Date: 97/05/02 02:00:47 $ $Revision: 1.157.98.32 $ PATCH_10.20 (PHKL_10757) /usr/conf/lib/libhp-ux.a(vm_machreg.o): vm_machreg.c $Date: 97/05/02 02:01:05 $ $Revision : 1.17.98.19 $ PATCH_10.20 (PHKL_10757) /usr/conf/lib/libhp-ux.a(vm_mmap.o): vm_mmap.c $Date: 96/11/20 11:02:00 $ $Revision: 1.17.98.14 $ PATCH_10.20 (PHKL_9075) /usr/conf/lib/libhp-ux.a(vm_pdir1_1.o): vm_pdir1_1.c $Date: 97/05/02 02:00:37 $ $Revision: 1.3.98.14 $ PATCH_10.20 (PHKL_10757) /usr/conf/lib/libhp-ux.a(vm_pdir2_0.o): vm_pdir2_0.c $Date: 97/06/18 13:12:17 $ $Revision: 1 .3.98.11 $ PATCH_10.20 (PHKL_11408) /usr/conf/lib/libhp-ux.a(vm_pregion.o): vm_pregion.c $Date: 97/04/07 13:34:27 $ $Revision: 1.16.98.13 $ PATCH_10.20 (PHKL_10643) /usr/conf/lib/libhp-ux.a(vm_region.o): vm_region.c $Date: 96/11/20 11:01:58 $ $Revision: 1.20.98.4 $ PATCH_10.20 (PHKL_9075) /usr/conf/lib/libhp-ux.a(vm_sched.o): vm_sched.c $Date: 96/11/20 11:01:54 $ $Revision: 1.58.98.9 $ PATCH_10.20 (PHKL_9075) /usr/conf/lib/libhp-ux.a(vm_superpage.o): vm_superpage.c $Date: 97/05/02 02:03:23 $ $Revisi on: 1.2.98.4 $ PATCH_10.20 (PHKL_10757) /usr/conf/lib/libhp-ux.a(vm_text.o): vm_text.c $Date: 97/03/03 12:25:55 $ $Revision: 1 .56.98.9 $ PATCH_10.20 (PHKL_10257) /usr/conf/lib/libhp-ux.a(vm_vas.o): vm_vas.c $Date: 97/05/02 02:03:25 $ $Revision: 1.18.98.15 $ PATCH_10.20 (PHKL_10757) /usr/conf/lib/libhp-ux.a(vm_vhand.o): vm_vhand.c $Date: 96/11/20 11:02:03 $ $Revision: 1.20.98.5 $ PATCH_10.20 (PHKL_9075) /usr/conf/lib/liblvm.a(lv_block.o): lv_block.c $Date: 96/10/25 20:54:08 $ $Revision: 1.1 3.98.4 $ PATCH_10.20 (PHKL_8999) /usr/conf/lib/liblvm.a(lv_cluster_lock.o): lv_cluster_lock.c $Date: 96/10/25 16:50:50 $ $Revisi on: 1.10.98.4 $ PATCH_10.20 (PHKL_8999) /usr/conf/lib/liblvm.a(lv_defect.o): lv_defect.c $Date: 96/10/25 17:01:38 $ $Revision: 1. 16.98.4 $ PATCH_10.20 (PHKL_8999) /usr/conf/lib/liblvm.a(lv_hp.o): lv_hp.c $Date: 97/05/13 13:53:54 $ $Revision: 1.18.9 8.20 $ PATCH_10.20 (PHKL_11085) /usr/conf/lib/liblvm.a(lv_ioctls.o): lv_ioctls.c $Date: 96/12/11 16:51:19 $ $Revision: 1. 18.98.14 $ PATCH_10.20 (PHKL_9529) /usr/conf/lib/liblvm.a(lv_kdb.o): lv_kdb.c $Date: 96/10/25 20:54:10 $ $Revision: 1.9.9 8.3 $ PATCH_10.20 (PHKL_8999) /usr/conf/lib/liblvm.a(lv_lvsubr.o): lv_lvsubr.c $Date: 97/05/13 13:51:54 $ $Revision: 1.15.98.14 $ PATCH_10.20 (PHKL_11085) /usr/conf/lib/liblvm.a(lv_malloc.o): lv_malloc.c $Date: 96/10/25 20:55:45 $ $Revision: 1. 11.98.3 $ PATCH_10.20 (PHKL_8999) /usr/conf/lib/liblvm.a(lv_mircons.o): lv_mircons.c $Date: 97/04/09 11:13:04 $ $Revision: 1 .14.98.6 $ PATCH_10.20 (PHKL_10675) /usr/conf/lib/liblvm.a(lv_pbuf.o): lv_pbuf.c $Date: 96/10/25 20:54:12 $ $Revision: 1.11 .98.6 $ PATCH_10.20 (PHKL_8999) /usr/conf/lib/liblvm.a(lv_phys.o): lv_phys.c $Date: 97/05/13 13:47:45 $ $Revision: 1.14 .98.11 $ PATCH_10.20 (PHKL_11085) /usr/conf/lib/liblvm.a(lv_schedule.o): lv_schedule.c $Date: 97/04/09 11:13:34 $ $Revision: 1.18.98.10 $ PATCH_10.20 (PHKL_10675) /usr/conf/lib/liblvm.a(lv_spare.o): lv_spare.c $Date: 96/10/28 11:23:00 $ $Revision: 1.3 .98.4 $ PATCH_10.20 (PHKL_8999) /usr/conf/lib/liblvm.a(lv_strategy.o): lv_strategy.c $Date: 97/04/09 11:13:41 $ $Revision: 1.14.98.6 $ PATCH_10.20 (PHKL_10675) /usr/conf/lib/liblvm.a(lv_stub.o): lv_stub.c $Date: 96/10/25 20:54:05 $ $Revision: 1.13 .98.2 $ PATCH_10.20 (PHKL_8999) /usr/conf/lib/liblvm.a(lv_subr.o): lv_subr.c $Date: 96/10/25 17:02:45 $ $Revision: 1.18 .98.6 $ PATCH_10.20 (PHKL_8999) /usr/conf/lib/liblvm.a(lv_syscalls.o): lv_syscalls.c $Date: 96/10/25 17:02:53 $ $Revision: 1.14.98.7 $ PATCH_10.20 (PHKL_8999) /usr/conf/lib/liblvm.a(lv_vgda.o): lv_vgda.c $Date: 96/10/25 17:03:01 $ $Revision: 1.18 .98.3 $ PATCH_10.20 (PHKL_8999) /usr/conf/lib/liblvm.a(lv_vgsa.o): lv_vgsa.c $Date: 96/10/25 17:03:05 $ $Revision: 1.14 .98.6 $ PATCH_10.20 (PHKL_8999) /usr/conf/lib/liblvm.a(sh_vgsa.o): sh_vgsa.c $Date: 96/10/25 17:03:23 $ $Revision: 1.3 .98.7 $ PATCH_10.20 (PHKL_8999) /usr/conf/lib/liblvm.a(slvm_comm.o): slvm_comm.c $Date: 96/10/25 17:03:40 $ $Revision: 1. 3.98.4 $ PATCH_10.20 (PHKL_8999) /usr/conf/lib/liblvm.a(slvm_schedule.o): slvm_schedule.c $Date: 96/10/25 17:03:49 $ $Revision : 1.3.98.6 $ PATCH_10.20 (PHKL_8999) /usr/conf/master.d/core-hpux: core-hpux $Date: 97/06/17 16:43:58 $ $Revision: 1. 6.98.15 $ PATCH_10.20 (PHKL_11406) /usr/conf/space.h.d/core-hpux.h: core-hpux.h $Date: 97/06/17 16:40:59 $ $Revision: 1.6.98.13 $ PATCH_10.20 (PHKL_11406) /usr/include/sys/audit.h: audit.h $Date: 97/04/21 13:54:38 $ $Revision: 1.10.98.5 $ PATCH_10.20 (PHKL_10800) cksum(1) Output: 309306691 13103 /usr/conf/h/audit.h 3294814409 19476 /usr/conf/lib/libhp-ux.a(asm_rv.o) 3109290296 7640 /usr/conf/lib/libhp-ux.a(asm_scall.o) 1231112847 18512 /usr/conf/lib/libhp-ux.a(asm_utl.o) 1650397953 4584 /usr/conf/lib/libhp-ux.a(asm_vm_pdir.o) 3455675956 4668 /usr/conf/lib/libhp-ux.a(bcopy.o) 4158269677 10276 /usr/conf/lib/libhp-ux.a(btlb.o) 4124458617 2432 /usr/conf/lib/libhp-ux.a(bzero.o) 1053092530 19912 /usr/conf/lib/libhp-ux.a(clock.o) 4114346575 11604 /usr/conf/lib/libhp-ux.a(cpd.o) 797819625 12752 /usr/conf/lib/libhp-ux.a(dump.o) 1084924137 8028 /usr/conf/lib/libhp-ux.a(flipper.o) 3189247447 13408 /usr/conf/lib/libhp-ux.a(hdl_fault.o) 555026448 6348 /usr/conf/lib/libhp-ux.a(hdl_init.o) 997333578 15648 /usr/conf/lib/libhp-ux.a(hdl_mprotect.o) 2213765960 11900 /usr/conf/lib/libhp-ux.a(hdl_policy.o) 2718340289 10016 /usr/conf/lib/libhp-ux.a(hdl_trans.o) 3231555571 18508 /usr/conf/lib/libhp-ux.a(init_main.o) 3476683986 6584 /usr/conf/lib/libhp-ux.a(interrupt.o) 4158272115 16888 /usr/conf/lib/libhp-ux.a(kern_exec.o) 303743927 15144 /usr/conf/lib/libhp-ux.a(kern_fork.o) 50317043 6492 /usr/conf/lib/libhp-ux.a(kern_kload.o) 4163060998 3948 /usr/conf/lib/libhp-ux.a(kern_mman.o) 2216617969 10284 /usr/conf/lib/libhp-ux.a(kern_sig.o) 3276898957 6160 /usr/conf/lib/libhp-ux.a(lbcopy.o) 300166288 2428 /usr/conf/lib/libhp-ux.a(lbzero.o) 3609837110 26628 /usr/conf/lib/libhp-ux.a(lv_config.o) 3955047993 156556 /usr/conf/lib/libhp-ux.a(lv_lvm.o) 228543399 7008 /usr/conf/lib/libhp-ux.a(lw_scall.o) 2457463992 3348 /usr/conf/lib/libhp-ux.a(outlaw.o) 3029803182 2988 /usr/conf/lib/libhp-ux.a(pgcopy.o) 1049043668 6184 /usr/conf/lib/libhp-ux.a(pm_clockint.o) 1701549902 5388 /usr/conf/lib/libhp-ux.a(pm_config.o) 3811483497 2236 /usr/conf/lib/libhp-ux.a(pm_context.o) 1145535485 6872 /usr/conf/lib/libhp-ux.a(pm_core.o) 280792863 17068 /usr/conf/lib/libhp-ux.a(pm_policy.o) 3933929381 17908 /usr/conf/lib/libhp-ux.a(pm_proc.o) 3189023695 6680 /usr/conf/lib/libhp-ux.a(pm_procdup.o) 3682830469 15732 /usr/conf/lib/libhp-ux.a(pm_ptrace.o) 775863340 7076 /usr/conf/lib/libhp-ux.a(pm_resource.o) 1066734922 16212 /usr/conf/lib/libhp-ux.a(pm_sendsig.o) 3521481640 11580 /usr/conf/lib/libhp-ux.a(pm_signal.o) 3746862926 20452 /usr/conf/lib/libhp-ux.a(pm_swtch.o) 3233056101 12032 /usr/conf/lib/libhp-ux.a(pm_threads.o) 2347361030 6324 /usr/conf/lib/libhp-ux.a(pm_timers.o) 18384036 11264 /usr/conf/lib/libhp-ux.a(protection.o) 4055553278 23840 /usr/conf/lib/libhp-ux.a(pstat.o) 2317800830 3876 /usr/conf/lib/libhp-ux.a(resume.o) 3665684469 9532 /usr/conf/lib/libhp-ux.a(sem_alpha.o) 3306390220 10616 /usr/conf/lib/libhp-ux.a(subr_ksleep.o) 947809473 10572 /usr/conf/lib/libhp-ux.a(subr_timers.o) 925297696 8712 /usr/conf/lib/libhp-ux.a(sysV_shm.o) 3959296490 6328 /usr/conf/lib/libhp-ux.a(ulbcopy.o) 3310110528 29820 /usr/conf/lib/libhp-ux.a(vfs_vm.o) 3286507644 91100 /usr/conf/lib/libhp-ux.a(vm_machdep.o) 3448592545 14300 /usr/conf/lib/libhp-ux.a(vm_machreg.o) 133406500 21604 /usr/conf/lib/libhp-ux.a(vm_mmap.o) 290807052 30900 /usr/conf/lib/libhp-ux.a(vm_pdir1_1.o) 1469266556 53368 /usr/conf/lib/libhp-ux.a(vm_pdir2_0.o) 1265397058 12324 /usr/conf/lib/libhp-ux.a(vm_pregion.o) 1266053234 11316 /usr/conf/lib/libhp-ux.a(vm_region.o) 3119256795 24816 /usr/conf/lib/libhp-ux.a(vm_sched.o) 1840315938 9988 /usr/conf/lib/libhp-ux.a(vm_superpage.o) 2800961341 14444 /usr/conf/lib/libhp-ux.a(vm_text.o) 3942568331 13348 /usr/conf/lib/libhp-ux.a(vm_vas.o) 1919993849 14372 /usr/conf/lib/libhp-ux.a(vm_vhand.o) 2908410957 2624 /usr/conf/lib/liblvm.a(lv_block.o) 3171795420 9956 /usr/conf/lib/liblvm.a(lv_cluster_lock.o) 896200314 12464 /usr/conf/lib/liblvm.a(lv_defect.o) 1900198770 83124 /usr/conf/lib/liblvm.a(lv_hp.o) 3824188877 31668 /usr/conf/lib/liblvm.a(lv_ioctls.o) 3467347777 728 /usr/conf/lib/liblvm.a(lv_kdb.o) 2376811084 36088 /usr/conf/lib/liblvm.a(lv_lvsubr.o) 71576499 2544 /usr/conf/lib/liblvm.a(lv_malloc.o) 4246721683 17420 /usr/conf/lib/liblvm.a(lv_mircons.o) 311558564 6568 /usr/conf/lib/liblvm.a(lv_pbuf.o) 2345382713 7724 /usr/conf/lib/liblvm.a(lv_phys.o) 3179031424 26360 /usr/conf/lib/liblvm.a(lv_schedule.o) 2221436812 36328 /usr/conf/lib/liblvm.a(lv_spare.o) 2281280116 7164 /usr/conf/lib/liblvm.a(lv_strategy.o) 4115391771 732 /usr/conf/lib/liblvm.a(lv_stub.o) 492882945 10056 /usr/conf/lib/liblvm.a(lv_subr.o) 1066182273 13520 /usr/conf/lib/liblvm.a(lv_syscalls.o) 4142623297 9100 /usr/conf/lib/liblvm.a(lv_vgda.o) 3239541967 12592 /usr/conf/lib/liblvm.a(lv_vgsa.o) 3517786406 41964 /usr/conf/lib/liblvm.a(sh_vgsa.o) 2159002800 27264 /usr/conf/lib/liblvm.a(slvm_comm.o) 4188283521 6724 /usr/conf/lib/liblvm.a(slvm_schedule.o) 245948872 16914 /usr/conf/master.d/core-hpux 1898168158 18969 /usr/conf/space.h.d/core-hpux.h 309306691 13103 /usr/include/sys/audit.h Patch Conflicts: None Patch Dependencies: s700: 10.20: PHCO_8871 Hardware Dependencies: None Other Dependencies: None Supersedes: PHKL_7870 PHKL_7951 PHKL_8084 PHKL_8346 PHKL_8532 PHKL_8716 PHKL_8999 PHKL_9075 PHKL_9151 PHKL_9273 PHKL_9529 PHKL_9919 PHKL_10176 PHKL_10234 PHKL_10257 PHKL_10316 PHKL_10452 PHKL_10554 PHKL_10643 PHKL_10675 PHKL_10689 PHKL_10757 PHKL_10800 PHKL_10821 PHKL_10932 PHKL_11006 PHKL_11085 PHKL_11238 PHKL_11339 PHKL_11406 Equivalent Patches: PHKL_11409: s800: 10.20 Patch Package Size: 1620 KBytes Installation Instructions: Please review all instructions and the Hewlett-Packard SupportLine User Guide or your Hewlett-Packard support terms and conditions for precautions, scope of license, restrictions, and, limitation of liability and warranties, before installing this patch. ------------------------------------------------------------ 1. Back up your system before installing a patch. 2. Login as root. 3. Copy the patch to the /tmp directory. 4. Move to the /tmp directory and unshar the patch: cd /tmp sh PHKL_11408 5a. For a standalone system, run swinstall to install the patch: swinstall -x autoreboot=true -x match_target=true \ -s /tmp/PHKL_11408.depot 5b. For a homogeneous NFS Diskless cluster run swcluster on the server to install the patch on the server and the clients: swcluster -i -b This will invoke swcluster in the interactive mode and force all clients to be shut down. WARNING: All cluster clients must be shut down prior to the patch installation. Installing the patch while the clients are booted is unsupported and can lead to serious problems. The swcluster command will invoke an swinstall session in which you must specify: alternate root path - default is /export/shared_root/OS_700 source depot path - /tmp/PHKL_11408.depot To complete the installation, select the patch by choosing "Actions -> Match What Target Has" and then "Actions -> Install" from the Menubar. 5c. For a heterogeneous NFS Diskless cluster: - run swinstall on the server as in step 5a to install the patch on the cluster server. - run swcluster on the server as in step 5b to install the patch on the cluster clients. By default swinstall will archive the original software in /var/adm/sw/patch/PHKL_11408. If you do not wish to retain a copy of the original software, you can create an empty file named /var/adm/sw/patch/PATCH_NOSAVE. Warning: If this file exists when a patch is installed, the patch cannot be deinstalled. Please be careful when using this feature. It is recommended that you move the PHKL_11408.text file to /var/adm/sw/patch for future reference. To put this patch on a magnetic tape and install from the tape drive, use the command: dd if=/tmp/PHKL_11408.depot of=/dev/rmt/0m bs=2k Special Installation Instructions: The default behavior of the sytem when this patch is nstalled is that the maximum size of the argument and environment strings that can be passed to EXEC wil be 20478 bytes (this is the same as the value that is defined by the constant ARG_MAX in /usr/include/limits.h). In this mode, the sysconf(_SC_ARG_MAX) call will also return this value. To enable the system to handle larger environments, a new parameter needs to be introduced in the system file as shown below: large_ncargs_enabled 1 With this change in the system file, a new kernel should be built and system rebooted, after which the sysconf(_SC_ARG_MAX) call will return the larger environment that is supported. The exact value will be 2048000. Due to the number of objects in this patch, the customization phase of the update may take more than 10 minutes. During that time the system will not appear to make forward progress, but it will actually be installing the objects.