Switch Mode Power Supply Testing Report Test Program Name : AX760 ATE - PK Serial No : Testing Data System Time : 2012/10/26 11:04:01 AM Model Name : SEASONIC AX760 Elapsed Time : 00:03:07 LOT Number : Environment : Order Number : Inspector : rayw Customer : Test Result : PASS ================================================================================ (Pre Test seq.1) : TTL & Relay PreSetup((Switch off)) Delay Time (ms) = 200 TTL State 1 = 0000 TTL State 2 = 0000 Relay State 1 = 00 Relay State 2 = 00 TTL Change State Delay (ms) = 200 Relay Change State Delay (ms) = 200 ================================================================================ (Pre Test seq.2) : Dynamic Load Value PreSetup Load Loading-1 Loading-2 Duration-1 Duration-2 Rise Rate Fall Rate Name (A) (A) (ms) (ms) (A/us) (A/us) ------------- --------- --------- ---------- ---------- --------- --------- 5V 0.400 10.090 10.000 10.000 1.0000 1.0000 3.3V 0.610 10.090 10.000 10.000 1.0000 1.0000 12V1 12.600 7.200 10.000 10.000 1.0000 1.0000 12V2 12.600 7.200 10.000 10.000 1.0000 1.0000 12V3 12.600 7.200 10.000 10.000 1.0000 1.0000 -12V 0.200 0.210 10.000 10.000 0.8000 0.8000 5VSB 0.000 1.260 10.000 10.000 0.8000 0.8000 12V4 12.600 7.200 10.000 10.000 1.0000 1.0000 12V5 12.600 7.200 10.000 10.000 1.0000 1.0000 ================================================================================ (Pre Test seq.3) : System Setup Vin (V)= 90.00 Maximum Input Voltage (V)= 300.00 Fin (Hz)= 60.00 Current Limit(A)= 30.00 Von Action Type(1:Latch 0:Nonlatch) = 1 Load Mode (0:CC, 1:CR, 2:CV) Load Load ILoad VLoad Von Rise Rate Fall Rate Name Mode Max(A) Max(V) (V) (A/us) (A/us) ------------- ----- ------ ------ ------ --------- --------- 5V 0 60.00 80.00 0.30 0.1000 0.1000 3.3V 0 60.00 80.00 0.30 0.1000 0.1000 12V1 0 60.00 80.00 0.30 0.1000 0.1000 12V2 0 60.00 80.00 0.30 0.1000 0.1000 12V3 0 60.00 80.00 0.30 0.1000 0.1000 -12V 0 20.00 80.00 -0.30 0.1000 0.1000 5VSB 0 20.00 80.00 0.50 0.1000 0.1000 12V4 0 60.00 80.00 0.30 0.1000 0.1000 12V5 0 60.00 80.00 0.30 0.1000 0.1000 ================================================================================ STEP.1(UUT Test seq.1) : TTL & Relay Setup((Switch on)) ------------------- PASS Delay Time (ms) = 3000 TTL State 1 = 0000 TTL State 2 = 0100 Relay State 1 = 00 Relay State 2 = 01 TTL Change State Delay (ms) = 200 Relay Change State Delay (ms) = 200 ================================================================================ STEP.2(UUT Test seq.2) : Voltage Regulation Test(Min Load (Load A) 90Vac-26 PASS Vin-1 (V)= 90.00 Fin-1 (Hz)= 47.00 Vin-2 (V)= 264.00 Fin-2 (Hz)= 63.00 Delay Time (ms)= 3000.00 Load Loading-1 Loading-2 Name (A/Ohm/V) (A/Ohm/V) ------------- ---------- ---------- 5V 0.000 0.000 3.3V 0.000 0.000 12V1 0.000 0.000 12V2 0.000 0.000 12V3 0.000 0.000 -12V 0.000 0.000 5VSB 0.000 0.000 12V4 0.000 0.000 12V5 0.000 0.000 Load Vout-1 Vout-1 Vout-1 Vout-2 Vout-2 Vout-2 Name Max Min (V) Max Min (V) ------------- ------- ------- ------- ------- ------- ------- 5V 5.150 4.850 5.050 5.150 4.850 5.050 3.3V 3.399 3.201 3.328 3.399 3.201 3.330 12V1 12.360 11.640 12.102 12.360 11.640 12.100 12V2 12.360 11.640 12.097 12.360 11.640 12.097 12V3 12.360 11.640 12.097 12.360 11.640 12.097 -12V -13.200 -10.800 -11.663 -13.200 -10.800 -11.655 5VSB 5.200 4.800 5.130 5.200 4.800 5.130 12V4 12.360 11.640 12.097 12.360 11.640 12.097 12V5 12.360 11.640 12.100 12.360 11.640 12.097 Load dVout dVout dVout Name Max Min (V) ------------- ------- ------- ------- 5V ******* ******* 0.000 3.3V ******* ******* 0.002 12V1 ******* ******* -0.002 12V2 ******* ******* 0.000 12V3 ******* ******* 0.000 -12V ******* ******* -0.008 5VSB ******* ******* 0.000 12V4 ******* ******* 0.000 12V5 ******* ******* -0.003 ================================================================================ STEP.3(UUT Test seq.3) : Voltage Regulation Test(80+ 20% Load 90Vac-264Vac) PASS Vin-1 (V)= 90.00 Fin-1 (Hz)= 47.00 Vin-2 (V)= 264.00 Fin-2 (Hz)= 63.00 Delay Time (ms)= 3000.00 Load Loading-1 Loading-2 Name (A/Ohm/V) (A/Ohm/V) ------------- ---------- ---------- 5V 2.540 2.540 3.3V 2.540 2.540 12V1 2.120 2.120 12V2 2.120 2.120 12V3 2.120 2.120 -12V 0.080 0.080 5VSB 0.510 0.510 12V4 2.120 2.120 12V5 2.120 2.120 Load Vout-1 Vout-1 Vout-1 Vout-2 Vout-2 Vout-2 Name Max Min (V) Max Min (V) ------------- ------- ------- ------- ------- ------- ------- 5V 5.150 4.850 5.048 5.150 4.850 5.048 3.3V 3.399 3.201 3.322 3.399 3.201 3.322 12V1 12.360 11.640 12.075 12.360 11.640 12.075 12V2 12.360 11.640 12.095 12.360 11.640 12.097 12V3 12.360 11.640 12.095 12.360 11.640 12.097 -12V -13.200 -10.800 -11.727 -13.200 -10.800 -11.730 5VSB 5.200 4.800 5.100 5.200 4.800 5.102 12V4 12.360 11.640 12.092 12.360 11.640 12.092 12V5 12.360 11.640 12.090 12.360 11.640 12.090 Load dVout dVout dVout Name Max Min (V) ------------- ------- ------- ------- 5V ******* ******* 0.000 3.3V ******* ******* 0.000 12V1 ******* ******* 0.000 12V2 ******* ******* 0.002 12V3 ******* ******* 0.002 -12V ******* ******* 0.002 5VSB ******* ******* 0.002 12V4 ******* ******* 0.000 12V5 ******* ******* 0.000 ================================================================================ STEP.4(UUT Test seq.4) : Voltage Regulation Test(80+ 50% Load 90Vac-264Vac) PASS Vin-1 (V)= 90.00 Fin-1 (Hz)= 47.00 Vin-2 (V)= 264.00 Fin-2 (Hz)= 63.00 Delay Time (ms)= 3000.00 Load Loading-1 Loading-2 Name (A/Ohm/V) (A/Ohm/V) ------------- ---------- ---------- 5V 6.340 6.340 3.3V 6.340 6.340 12V1 5.310 5.310 12V2 5.310 5.310 12V3 5.310 5.310 -12V 0.210 0.210 5VSB 1.260 1.260 12V4 5.310 5.310 12V5 5.310 5.310 Load Vout-1 Vout-1 Vout-1 Vout-2 Vout-2 Vout-2 Name Max Min (V) Max Min (V) ------------- ------- ------- ------- ------- ------- ------- 5V 5.150 4.850 5.040 5.150 4.850 5.040 3.3V 3.399 3.201 3.315 3.399 3.201 3.313 12V1 12.360 11.640 12.038 12.360 11.640 12.038 12V2 12.360 11.640 12.097 12.360 11.640 12.095 12V3 12.360 11.640 12.100 12.360 11.640 12.100 -12V -13.200 -10.800 -11.752 -13.200 -10.800 -11.752 5VSB 5.200 4.800 5.057 5.200 4.800 5.057 12V4 12.360 11.640 12.085 12.360 11.640 12.087 12V5 12.360 11.640 12.080 12.360 11.640 12.080 Load dVout dVout dVout Name Max Min (V) ------------- ------- ------- ------- 5V ******* ******* 0.000 3.3V ******* ******* -0.002 12V1 ******* ******* 0.000 12V2 ******* ******* -0.002 12V3 ******* ******* 0.000 -12V ******* ******* 0.000 5VSB ******* ******* 0.000 12V4 ******* ******* 0.002 12V5 ******* ******* 0.000 ================================================================================ STEP.5(UUT Test seq.5) : Voltage Regulation Test(80+ 100% Load 90Vac-264Vac PASS Vin-1 (V)= 90.00 Fin-1 (Hz)= 47.00 Vin-2 (V)= 264.00 Fin-2 (Hz)= 63.00 Delay Time (ms)= 3000.00 Load Loading-1 Loading-2 Name (A/Ohm/V) (A/Ohm/V) ------------- ---------- ---------- 5V 12.690 12.690 3.3V 12.690 12.690 12V1 10.620 10.620 12V2 10.620 10.620 12V3 10.620 10.620 -12V 0.420 0.420 5VSB 2.530 2.530 12V4 10.620 10.620 12V5 10.620 10.620 Load Vout-1 Vout-1 Vout-1 Vout-2 Vout-2 Vout-2 Name Max Min (V) Max Min (V) ------------- ------- ------- ------- ------- ------- ------- 5V 5.150 4.850 5.028 5.150 4.850 5.030 3.3V 3.399 3.201 3.297 3.399 3.201 3.297 12V1 12.360 11.640 11.970 12.360 11.640 11.970 12V2 12.360 11.640 12.092 12.360 11.640 12.092 12V3 12.360 11.640 12.100 12.360 11.640 12.100 -12V -13.200 -10.800 -11.977 -13.200 -10.800 -11.985 5VSB 5.200 4.800 4.990 5.200 4.800 4.992 12V4 12.360 11.640 12.078 12.360 11.640 12.075 12V5 12.360 11.640 12.060 12.360 11.640 12.060 Load dVout dVout dVout Name Max Min (V) ------------- ------- ------- ------- 5V ******* ******* 0.002 3.3V ******* ******* 0.000 12V1 ******* ******* 0.000 12V2 ******* ******* 0.000 12V3 ******* ******* 0.000 -12V ******* ******* 0.007 5VSB ******* ******* 0.002 12V4 ******* ******* -0.003 12V5 ******* ******* 0.000 ================================================================================ STEP.6(UUT Test seq.6) : Voltage Regulation Test(12V Full Load 90Vac-264Vac PASS Vin-1 (V)= 90.00 Fin-1 (Hz)= 47.00 Vin-2 (V)= 264.00 Fin-2 (Hz)= 63.00 Delay Time (ms)= 3000.00 Load Loading-1 Loading-2 Name (A/Ohm/V) (A/Ohm/V) ------------- ---------- ---------- 5V 0.400 0.400 3.3V 0.610 0.610 12V1 12.600 12.600 12V2 12.600 12.600 12V3 12.600 12.600 -12V 0.200 0.200 5VSB 0.000 0.000 12V4 12.600 12.600 12V5 12.600 12.600 Load Vout-1 Vout-1 Vout-1 Vout-2 Vout-2 Vout-2 Name Max Min (V) Max Min (V) ------------- ------- ------- ------- ------- ------- ------- 5V 5.150 4.850 5.043 5.150 4.850 5.043 3.3V 3.399 3.201 3.320 3.399 3.201 3.318 12V1 12.360 11.640 11.975 12.360 11.640 11.972 12V2 12.360 11.640 12.118 12.360 11.640 12.115 12V3 12.360 11.640 12.125 12.360 11.640 12.123 -12V -13.200 -10.800 -12.205 -13.200 -10.800 -12.203 5VSB 5.200 4.800 5.077 5.200 4.800 5.077 12V4 12.360 11.640 12.092 12.360 11.640 12.092 12V5 12.360 11.640 12.073 12.360 11.640 12.073 Load dVout dVout dVout Name Max Min (V) ------------- ------- ------- ------- 5V ******* ******* 0.000 3.3V ******* ******* -0.002 12V1 ******* ******* -0.003 12V2 ******* ******* -0.003 12V3 ******* ******* -0.002 -12V ******* ******* -0.002 5VSB ******* ******* 0.000 12V4 ******* ******* 0.000 12V5 ******* ******* 0.000 ================================================================================ STEP.7(UUT Test seq.7) : Voltage Regulation Test(Peak Load 115Vac-230Vac 17 PASS Vin-1 (V)= 115.00 Fin-1 (Hz)= 60.00 Vin-2 (V)= 230.00 Fin-2 (Hz)= 50.00 Delay Time (ms)= 17000.00 Load Loading-1 Loading-2 Name (A/Ohm/V) (A/Ohm/V) ------------- ---------- ---------- 5V 12.690 12.690 3.3V 12.690 12.690 12V1 11.880 11.880 12V2 11.880 11.880 12V3 11.880 11.880 -12V 0.420 0.420 5VSB 2.530 2.530 12V4 11.880 11.880 12V5 11.880 11.880 Load Vout-1 Vout-1 Vout-1 Vout-2 Vout-2 Vout-2 Name Max Min (V) Max Min (V) ------------- ------- ------- ------- ------- ------- ------- 5V 5.150 4.850 5.030 5.150 4.850 5.030 3.3V 3.399 3.201 3.297 3.399 3.201 3.297 12V1 12.360 11.640 11.955 12.360 11.640 11.960 12V2 12.360 11.640 12.102 12.360 11.640 12.090 12V3 12.360 11.640 12.102 12.360 11.640 12.113 -12V -13.200 -10.800 -12.095 -13.200 -10.800 -12.097 5VSB 5.200 4.800 4.985 5.200 4.800 4.985 12V4 12.360 11.640 12.083 12.360 11.640 12.070 12V5 12.360 11.640 12.057 12.360 11.640 12.060 Load dVout dVout dVout Name Max Min (V) ------------- ------- ------- ------- 5V ******* ******* 0.000 3.3V ******* ******* 0.000 12V1 ******* ******* 0.005 12V2 ******* ******* -0.013 12V3 ******* ******* 0.010 -12V ******* ******* 0.002 5VSB ******* ******* 0.000 12V4 ******* ******* -0.013 12V5 ******* ******* 0.003 ================================================================================ STEP.8(UUT Test seq.8) : Voltage Regulation Test(Load 1 (+5V FL) 90Vac-264V PASS Vin-1 (V)= 90.00 Fin-1 (Hz)= 47.00 Vin-2 (V)= 264.00 Fin-2 (Hz)= 63.00 Delay Time (ms)= 3000.00 Load Loading-1 Loading-2 Name (A/Ohm/V) (A/Ohm/V) ------------- ---------- ---------- 5V 25.000 25.000 3.3V 0.000 0.000 12V1 10.230 10.230 12V2 10.230 10.230 12V3 10.230 10.230 -12V 0.500 0.500 5VSB 3.000 3.000 12V4 10.230 10.230 12V5 10.230 10.230 Load Vout-1 Vout-1 Vout-1 Vout-2 Vout-2 Vout-2 Name Max Min (V) Max Min (V) ------------- ------- ------- ------- ------- ------- ------- 5V 5.150 4.850 5.020 5.150 4.850 5.023 3.3V 3.399 3.201 3.318 3.399 3.201 3.318 12V1 12.360 11.640 11.975 12.360 11.640 11.975 12V2 12.360 11.640 12.090 12.360 11.640 12.092 12V3 12.360 11.640 12.102 12.360 11.640 12.100 -12V -13.200 -10.800 -11.950 -13.200 -10.800 -11.953 5VSB 5.200 4.800 4.977 5.200 4.800 4.980 12V4 12.360 11.640 12.078 12.360 11.640 12.078 12V5 12.360 11.640 12.063 12.360 11.640 12.063 Load dVout dVout dVout Name Max Min (V) ------------- ------- ------- ------- 5V ******* ******* 0.002 3.3V ******* ******* 0.000 12V1 ******* ******* 0.000 12V2 ******* ******* 0.002 12V3 ******* ******* -0.002 -12V ******* ******* 0.003 5VSB ******* ******* 0.002 12V4 ******* ******* 0.000 12V5 ******* ******* 0.000 ================================================================================ STEP.9(UUT Test seq.9) : Voltage Regulation Test(Load 2 (+3.3V FL) 90Vac-26 PASS Vin-1 (V)= 90.00 Fin-1 (Hz)= 47.00 Vin-2 (V)= 264.00 Fin-2 (Hz)= 63.00 Delay Time (ms)= 3000.00 Load Loading-1 Loading-2 Name (A/Ohm/V) (A/Ohm/V) ------------- ---------- ---------- 5V 8.500 8.500 3.3V 25.000 25.000 12V1 10.230 10.230 12V2 10.230 10.230 12V3 10.230 10.230 -12V 0.500 0.500 5VSB 3.000 3.000 12V4 10.230 10.230 12V5 10.230 10.230 Load Vout-1 Vout-1 Vout-1 Vout-2 Vout-2 Vout-2 Name Max Min (V) Max Min (V) ------------- ------- ------- ------- ------- ------- ------- 5V 5.150 4.850 5.030 5.150 4.850 5.030 3.3V 3.399 3.201 3.280 3.399 3.201 3.280 12V1 12.360 11.640 11.970 12.360 11.640 11.967 12V2 12.360 11.640 12.090 12.360 11.640 12.087 12V3 12.360 11.640 12.097 12.360 11.640 12.097 -12V -13.200 -10.800 -11.965 -13.200 -10.800 -11.962 5VSB 5.200 4.800 4.972 5.200 4.800 4.972 12V4 12.360 11.640 12.073 12.360 11.640 12.073 12V5 12.360 11.640 12.060 12.360 11.640 12.057 Load dVout dVout dVout Name Max Min (V) ------------- ------- ------- ------- 5V ******* ******* 0.000 3.3V ******* ******* 0.000 12V1 ******* ******* -0.003 12V2 ******* ******* -0.003 12V3 ******* ******* 0.000 -12V ******* ******* -0.003 5VSB ******* ******* 0.000 12V4 ******* ******* 0.000 12V5 ******* ******* -0.003 ================================================================================ STEP.10(UUT Test seq.10) : Voltage Regulation Test(Load 4 (+5V +3.3V FL, 0A PASS Vin-1 (V)= 90.00 Fin-1 (Hz)= 47.00 Vin-2 (V)= 264.00 Fin-2 (Hz)= 63.00 Delay Time (ms)= 3000.00 Load Loading-1 Loading-2 Name (A/Ohm/V) (A/Ohm/V) ------------- ---------- ---------- 5V 12.500 12.500 3.3V 18.940 18.940 12V1 0.000 0.000 12V2 0.000 0.000 12V3 0.000 0.000 -12V 0.000 0.000 5VSB 0.000 0.000 12V4 0.000 0.000 12V5 0.000 0.000 Load Vout-1 Vout-1 Vout-1 Vout-2 Vout-2 Vout-2 Name Max Min (V) Max Min (V) ------------- ------- ------- ------- ------- ------- ------- 5V 5.150 4.850 5.037 5.150 4.850 5.037 3.3V 3.399 3.201 3.297 3.399 3.201 3.297 12V1 12.360 11.640 12.075 12.360 11.640 12.075 12V2 12.360 11.640 12.075 12.360 11.640 12.075 12V3 12.360 11.640 12.078 12.360 11.640 12.078 -12V -13.200 -10.800 -12.858 -13.200 -10.800 -12.858 5VSB 5.200 4.800 5.100 5.200 4.800 5.100 12V4 12.360 11.640 12.075 12.360 11.640 12.078 12V5 12.360 11.640 12.078 12.360 11.640 12.080 Load dVout dVout dVout Name Max Min (V) ------------- ------- ------- ------- 5V ******* ******* 0.000 3.3V ******* ******* 0.000 12V1 ******* ******* 0.000 12V2 ******* ******* 0.000 12V3 ******* ******* 0.000 -12V ******* ******* 0.000 5VSB ******* ******* 0.000 12V4 ******* ******* 0.003 12V5 ******* ******* 0.002 ================================================================================ STEP.11(UUT Test seq.11) : Voltage Regulation Test(Load 10 (+12V FL, 0A) (L PASS Vin-1 (V)= 90.00 Fin-1 (Hz)= 47.00 Vin-2 (V)= 264.00 Fin-2 (Hz)= 63.00 Delay Time (ms)= 3000.00 Load Loading-1 Loading-2 Name (A/Ohm/V) (A/Ohm/V) ------------- ---------- ---------- 5V 0.000 0.000 3.3V 0.000 0.000 12V1 12.600 12.600 12V2 12.600 12.600 12V3 12.600 12.600 -12V 0.200 0.200 5VSB 0.000 0.000 12V4 12.600 12.600 12V5 12.600 12.600 Load Vout-1 Vout-1 Vout-1 Vout-2 Vout-2 Vout-2 Name Max Min (V) Max Min (V) ------------- ------- ------- ------- ------- ------- ------- 5V 5.150 4.850 5.045 5.150 4.850 5.045 3.3V 3.399 3.201 3.320 3.399 3.201 3.320 12V1 12.360 11.640 11.975 12.360 11.640 11.977 12V2 12.360 11.640 12.115 12.360 11.640 12.120 12V3 12.360 11.640 12.125 12.360 11.640 12.127 -12V -13.200 -10.800 -12.222 -13.200 -10.800 -12.220 5VSB 5.200 4.800 5.080 5.200 4.800 5.080 12V4 12.360 11.640 12.097 12.360 11.640 12.095 12V5 12.360 11.640 12.075 12.360 11.640 12.078 Load dVout dVout dVout Name Max Min (V) ------------- ------- ------- ------- 5V ******* ******* 0.000 3.3V ******* ******* 0.000 12V1 ******* ******* 0.002 12V2 ******* ******* 0.005 12V3 ******* ******* 0.002 -12V ******* ******* -0.002 5VSB ******* ******* 0.000 12V4 ******* ******* -0.002 12V5 ******* ******* 0.003 ================================================================================ STEP.12(UUT Test seq.12) : Voltage Regulation Test(Load 11 (+5V +3.3V FL, + PASS Vin-1 (V)= 90.00 Fin-1 (Hz)= 47.00 Vin-2 (V)= 264.00 Fin-2 (Hz)= 63.00 Delay Time (ms)= 3000.00 Load Loading-1 Loading-2 Name (A/Ohm/V) (A/Ohm/V) ------------- ---------- ---------- 5V 12.500 12.500 3.3V 18.940 18.940 12V1 10.580 10.580 12V2 10.580 10.580 12V3 10.580 10.580 -12V 0.200 0.200 5VSB 0.000 0.000 12V4 10.580 10.580 12V5 10.580 10.580 Load Vout-1 Vout-1 Vout-1 Vout-2 Vout-2 Vout-2 Name Max Min (V) Max Min (V) ------------- ------- ------- ------- ------- ------- ------- 5V 5.150 4.850 5.030 5.150 4.850 5.030 3.3V 3.399 3.201 3.290 3.399 3.201 3.287 12V1 12.360 11.640 11.970 12.360 11.640 11.967 12V2 12.360 11.640 12.090 12.360 11.640 12.092 12V3 12.360 11.640 12.100 12.360 11.640 12.100 -12V -13.200 -10.800 -12.235 -13.200 -10.800 -12.235 5VSB 5.200 4.800 5.057 5.200 4.800 5.060 12V4 12.360 11.640 12.078 12.360 11.640 12.075 12V5 12.360 11.640 12.060 12.360 11.640 12.060 Load dVout dVout dVout Name Max Min (V) ------------- ------- ------- ------- 5V ******* ******* 0.000 3.3V ******* ******* -0.002 12V1 ******* ******* -0.003 12V2 ******* ******* 0.002 12V3 ******* ******* 0.000 -12V ******* ******* 0.000 5VSB ******* ******* 0.002 12V4 ******* ******* -0.003 12V5 ******* ******* 0.000 ================================================================================ STEP.13(UUT Test seq.13) : Noise Test(Min Load (Load A) 90Vac) ------------ PASS Vin (V)= 90.00 Fin (Hz)= 47.00 Delay Time (ms)= 3000.00 Load Noise Range Noise B.W Name (V) (MHz) ------------- ----------- --------- 5V 0.400 20.00 3.3V 0.400 20.00 12V1 0.400 20.00 12V2 0.400 20.00 12V3 0.400 20.00 -12V 0.400 20.00 5VSB 0.400 20.00 12V4 0.400 20.00 12V5 0.400 20.00 Load Loading Vpp Noise Vpp Noise Vpp Noise Name (A/Ohm/V) Max Min (V) ------------- --------- --------- --------- -------- 5V 0.000 0.035 ******* 0.0086 3.3V 0.000 0.030 ******* 0.0052 12V1 0.000 0.060 ******* 0.0052 12V2 0.000 0.060 ******* 0.0037 12V3 0.000 0.060 ******* 0.0035 -12V 0.000 0.060 ******* 0.0042 5VSB 0.000 0.040 ******* 0.0073 12V4 0.000 0.060 ******* 0.0038 12V5 0.000 0.060 ******* 0.0033 ================================================================================ STEP.14(UUT Test seq.14) : Noise Test(80+ 20% Load 90Vac) ----------------- PASS Vin (V)= 90.00 Fin (Hz)= 47.00 Delay Time (ms)= 1000.00 Load Noise Range Noise B.W Name (V) (MHz) ------------- ----------- --------- 5V 0.400 20.00 3.3V 0.400 20.00 12V1 0.400 20.00 12V2 0.400 20.00 12V3 0.400 20.00 -12V 0.400 20.00 5VSB 0.400 20.00 12V4 0.400 20.00 12V5 0.400 20.00 Load Loading Vpp Noise Vpp Noise Vpp Noise Name (A/Ohm/V) Max Min (V) ------------- --------- --------- --------- -------- 5V 2.540 0.035 ******* 0.0094 3.3V 2.540 0.030 ******* 0.0061 12V1 2.120 0.060 ******* 0.0193 12V2 2.120 0.060 ******* 0.0175 12V3 2.120 0.060 ******* 0.0174 -12V 0.080 0.060 ******* 0.0116 5VSB 0.510 0.040 ******* 0.0081 12V4 2.120 0.060 ******* 0.0178 12V5 2.120 0.060 ******* 0.0172 ================================================================================ STEP.15(UUT Test seq.15) : Noise Test(80+ 50% Load 90Vac) ----------------- PASS Vin (V)= 90.00 Fin (Hz)= 47.00 Delay Time (ms)= 1000.00 Load Noise Range Noise B.W Name (V) (MHz) ------------- ----------- --------- 5V 0.400 20.00 3.3V 0.400 20.00 12V1 0.400 20.00 12V2 0.400 20.00 12V3 0.400 20.00 -12V 0.400 20.00 5VSB 0.400 20.00 12V4 0.400 20.00 12V5 0.400 20.00 Load Loading Vpp Noise Vpp Noise Vpp Noise Name (A/Ohm/V) Max Min (V) ------------- --------- --------- --------- -------- 5V 6.340 0.035 ******* 0.0118 3.3V 6.340 0.030 ******* 0.0091 12V1 5.310 0.060 ******* 0.0258 12V2 5.310 0.060 ******* 0.0222 12V3 5.310 0.060 ******* 0.0239 -12V 0.210 0.060 ******* 0.0198 5VSB 1.260 0.040 ******* 0.0140 12V4 5.310 0.060 ******* 0.0232 12V5 5.310 0.060 ******* 0.0239 ================================================================================ STEP.16(UUT Test seq.16) : Noise Test(80+ 100% Load 90Vac) ---------------- PASS Vin (V)= 90.00 Fin (Hz)= 47.00 Delay Time (ms)= 1000.00 Load Noise Range Noise B.W Name (V) (MHz) ------------- ----------- --------- 5V 0.400 20.00 3.3V 0.400 20.00 12V1 0.400 20.00 12V2 0.400 20.00 12V3 0.400 20.00 -12V 0.400 20.00 5VSB 0.400 20.00 12V4 0.400 20.00 12V5 0.400 20.00 Load Loading Vpp Noise Vpp Noise Vpp Noise Name (A/Ohm/V) Max Min (V) ------------- --------- --------- --------- -------- 5V 12.690 0.035 ******* 0.0160 3.3V 12.690 0.030 ******* 0.0154 12V1 10.620 0.060 ******* 0.0340 12V2 10.620 0.060 ******* 0.0272 12V3 10.620 0.060 ******* 0.0319 -12V 0.420 0.060 ******* 0.0353 5VSB 2.530 0.040 ******* 0.0093 12V4 10.620 0.060 ******* 0.0290 12V5 10.620 0.060 ******* 0.0316 ================================================================================ STEP.17(UUT Test seq.17) : Noise Test(12V Full Load 90Vac (Load D)) ------- PASS Vin (V)= 90.00 Fin (Hz)= 47.00 Delay Time (ms)= 1000.00 Load Noise Range Noise B.W Name (V) (MHz) ------------- ----------- --------- 5V 0.400 20.00 3.3V 0.400 20.00 12V1 0.400 20.00 12V2 0.400 20.00 12V3 0.400 20.00 -12V 0.400 20.00 5VSB 0.400 20.00 12V4 0.400 20.00 12V5 0.400 20.00 Load Loading Vpp Noise Vpp Noise Vpp Noise Name (A/Ohm/V) Max Min (V) ------------- --------- --------- --------- -------- 5V 0.400 0.035 ******* 0.0123 3.3V 0.610 0.030 ******* 0.0107 12V1 12.600 0.060 ******* 0.0323 12V2 12.600 0.060 ******* 0.0268 12V3 12.600 0.060 ******* 0.0306 -12V 0.200 0.060 ******* 0.0236 5VSB 0.000 0.040 ******* 0.0131 12V4 12.600 0.060 ******* 0.0277 12V5 12.600 0.060 ******* 0.0311 ================================================================================ STEP.18(UUT Test seq.18) : Noise Test(Load 1 (+5V FL) 90Vac) -------------- PASS Vin (V)= 90.00 Fin (Hz)= 47.00 Delay Time (ms)= 1000.00 Load Noise Range Noise B.W Name (V) (MHz) ------------- ----------- --------- 5V 0.400 20.00 3.3V 0.400 20.00 12V1 0.400 20.00 12V2 0.400 20.00 12V3 0.400 20.00 -12V 0.400 20.00 5VSB 0.400 20.00 12V4 0.400 20.00 12V5 0.400 20.00 Load Loading Vpp Noise Vpp Noise Vpp Noise Name (A/Ohm/V) Max Min (V) ------------- --------- --------- --------- -------- 5V 25.000 0.035 ******* 0.0203 3.3V 0.000 0.030 ******* 0.0141 12V1 10.230 0.060 ******* 0.0355 12V2 10.230 0.060 ******* 0.0271 12V3 10.230 0.060 ******* 0.0324 -12V 0.500 0.060 ******* 0.0396 5VSB 3.000 0.040 ******* 0.0103 12V4 10.230 0.060 ******* 0.0294 12V5 10.230 0.060 ******* 0.0307 ================================================================================ STEP.19(UUT Test seq.19) : Noise Test(Load 2 (+3.3V FL) 90Vac) ------------ PASS Vin (V)= 90.00 Fin (Hz)= 47.00 Delay Time (ms)= 1000.00 Load Noise Range Noise B.W Name (V) (MHz) ------------- ----------- --------- 5V 0.400 20.00 3.3V 0.400 20.00 12V1 0.400 20.00 12V2 0.400 20.00 12V3 0.400 20.00 -12V 0.400 20.00 5VSB 0.400 20.00 12V4 0.400 20.00 12V5 0.400 20.00 Load Loading Vpp Noise Vpp Noise Vpp Noise Name (A/Ohm/V) Max Min (V) ------------- --------- --------- --------- -------- 5V 8.500 0.035 ******* 0.0181 3.3V 25.000 0.030 ******* 0.0184 12V1 10.230 0.060 ******* 0.0356 12V2 10.230 0.060 ******* 0.0266 12V3 10.230 0.060 ******* 0.0322 -12V 0.500 0.060 ******* 0.0400 5VSB 3.000 0.040 ******* 0.0090 12V4 10.230 0.060 ******* 0.0292 12V5 10.230 0.060 ******* 0.0311 ================================================================================ STEP.20(UUT Test seq.20) : Noise Test(Load 4 (+5V +3.3V FL, 0A) (Load B) 90 PASS Vin (V)= 90.00 Fin (Hz)= 47.00 Delay Time (ms)= 1000.00 Load Noise Range Noise B.W Name (V) (MHz) ------------- ----------- --------- 5V 0.400 20.00 3.3V 0.400 20.00 12V1 0.400 20.00 12V2 0.400 20.00 12V3 0.400 20.00 -12V 0.400 20.00 5VSB 0.400 20.00 12V4 0.400 20.00 12V5 0.400 20.00 Load Loading Vpp Noise Vpp Noise Vpp Noise Name (A/Ohm/V) Max Min (V) ------------- --------- --------- --------- -------- 5V 12.500 0.035 ******* 0.0131 3.3V 18.940 0.030 ******* 0.0121 12V1 0.000 0.060 ******* 0.0209 12V2 0.000 0.060 ******* 0.0171 12V3 0.000 0.060 ******* 0.0185 -12V 0.000 0.060 ******* 0.0051 5VSB 0.000 0.040 ******* 0.0076 12V4 0.000 0.060 ******* 0.0188 12V5 0.000 0.060 ******* 0.0171 ================================================================================ STEP.21(UUT Test seq.21) : Noise Test(Load 10 (+12V FL, 0A) (Load E) 90Vac) PASS Vin (V)= 90.00 Fin (Hz)= 47.00 Delay Time (ms)= 1000.00 Load Noise Range Noise B.W Name (V) (MHz) ------------- ----------- --------- 5V 0.400 20.00 3.3V 0.400 20.00 12V1 0.400 20.00 12V2 0.400 20.00 12V3 0.400 20.00 -12V 0.400 20.00 5VSB 0.400 20.00 12V4 0.400 20.00 12V5 0.400 20.00 Load Loading Vpp Noise Vpp Noise Vpp Noise Name (A/Ohm/V) Max Min (V) ------------- --------- --------- --------- -------- 5V 0.000 0.035 ******* 0.0123 3.3V 0.000 0.030 ******* 0.0109 12V1 12.600 0.060 ******* 0.0325 12V2 12.600 0.060 ******* 0.0269 12V3 12.600 0.060 ******* 0.0309 -12V 0.200 0.060 ******* 0.0239 5VSB 0.000 0.040 ******* 0.0131 12V4 12.600 0.060 ******* 0.0277 12V5 12.600 0.060 ******* 0.0312 ================================================================================ STEP.22(UUT Test seq.22) : Noise Test(Load 11 (+5V +3.3V FL, +12V) (Load C) PASS Vin (V)= 90.00 Fin (Hz)= 47.00 Delay Time (ms)= 1000.00 Load Noise Range Noise B.W Name (V) (MHz) ------------- ----------- --------- 5V 0.400 20.00 3.3V 0.400 20.00 12V1 0.400 20.00 12V2 0.400 20.00 12V3 0.400 20.00 -12V 0.400 20.00 5VSB 0.400 20.00 12V4 0.400 20.00 12V5 0.400 20.00 Load Loading Vpp Noise Vpp Noise Vpp Noise Name (A/Ohm/V) Max Min (V) ------------- --------- --------- --------- -------- 5V 12.500 0.035 ******* 0.0169 3.3V 18.940 0.030 ******* 0.0169 12V1 10.580 0.060 ******* 0.0345 12V2 10.580 0.060 ******* 0.0264 12V3 10.580 0.060 ******* 0.0316 -12V 0.200 0.060 ******* 0.0257 5VSB 0.000 0.040 ******* 0.0134 12V4 10.580 0.060 ******* 0.0287 12V5 10.580 0.060 ******* 0.0308 ================================================================================ STEP.23(UUT Test seq.23) : Noise Test(Min Load (Load A) 264Vac) ----------- PASS Vin (V)= 264.00 Fin (Hz)= 63.00 Delay Time (ms)= 3000.00 Load Noise Range Noise B.W Name (V) (MHz) ------------- ----------- --------- 5V 0.400 20.00 3.3V 0.400 20.00 12V1 0.400 20.00 12V2 0.400 20.00 12V3 0.400 20.00 -12V 0.400 20.00 5VSB 0.400 20.00 12V4 0.400 20.00 12V5 0.400 20.00 Load Loading Vpp Noise Vpp Noise Vpp Noise Name (A/Ohm/V) Max Min (V) ------------- --------- --------- --------- -------- 5V 0.000 0.035 ******* 0.0078 3.3V 0.000 0.030 ******* 0.0043 12V1 0.000 0.060 ******* 0.0027 12V2 0.000 0.060 ******* 0.0017 12V3 0.000 0.060 ******* 0.0011 -12V 0.000 0.060 ******* 0.0029 5VSB 0.000 0.040 ******* 0.0070 12V4 0.000 0.060 ******* 0.0016 12V5 0.000 0.060 ******* 0.0011 ================================================================================ STEP.24(UUT Test seq.24) : Noise Test(80+ 20% Load 264Vac) ---------------- PASS Vin (V)= 264.00 Fin (Hz)= 63.00 Delay Time (ms)= 1000.00 Load Noise Range Noise B.W Name (V) (MHz) ------------- ----------- --------- 5V 0.400 20.00 3.3V 0.400 20.00 12V1 0.400 20.00 12V2 0.400 20.00 12V3 0.400 20.00 -12V 0.400 20.00 5VSB 0.400 20.00 12V4 0.400 20.00 12V5 0.400 20.00 Load Loading Vpp Noise Vpp Noise Vpp Noise Name (A/Ohm/V) Max Min (V) ------------- --------- --------- --------- -------- 5V 2.540 0.035 ******* 0.0097 3.3V 2.540 0.030 ******* 0.0058 12V1 2.120 0.060 ******* 0.0227 12V2 2.120 0.060 ******* 0.0213 12V3 2.120 0.060 ******* 0.0213 -12V 0.080 0.060 ******* 0.0102 5VSB 0.510 0.040 ******* 0.0076 12V4 2.120 0.060 ******* 0.0217 12V5 2.120 0.060 ******* 0.0213 ================================================================================ STEP.25(UUT Test seq.25) : Noise Test(80+ 50% Load 264Vac) ---------------- PASS Vin (V)= 264.00 Fin (Hz)= 63.00 Delay Time (ms)= 1000.00 Load Noise Range Noise B.W Name (V) (MHz) ------------- ----------- --------- 5V 0.400 20.00 3.3V 0.400 20.00 12V1 0.400 20.00 12V2 0.400 20.00 12V3 0.400 20.00 -12V 0.400 20.00 5VSB 0.400 20.00 12V4 0.400 20.00 12V5 0.400 20.00 Load Loading Vpp Noise Vpp Noise Vpp Noise Name (A/Ohm/V) Max Min (V) ------------- --------- --------- --------- -------- 5V 6.340 0.035 ******* 0.0113 3.3V 6.340 0.030 ******* 0.0079 12V1 5.310 0.060 ******* 0.0261 12V2 5.310 0.060 ******* 0.0226 12V3 5.310 0.060 ******* 0.0246 -12V 0.210 0.060 ******* 0.0186 5VSB 1.260 0.040 ******* 0.0136 12V4 5.310 0.060 ******* 0.0238 12V5 5.310 0.060 ******* 0.0243 ================================================================================ STEP.26(UUT Test seq.26) : Noise Test(80+ 100% Load 264Vac) --------------- PASS Vin (V)= 264.00 Fin (Hz)= 63.00 Delay Time (ms)= 1000.00 Load Noise Range Noise B.W Name (V) (MHz) ------------- ----------- --------- 5V 0.400 20.00 3.3V 0.400 20.00 12V1 0.400 20.00 12V2 0.400 20.00 12V3 0.400 20.00 -12V 0.400 20.00 5VSB 0.400 20.00 12V4 0.400 20.00 12V5 0.400 20.00 Load Loading Vpp Noise Vpp Noise Vpp Noise Name (A/Ohm/V) Max Min (V) ------------- --------- --------- --------- -------- 5V 12.690 0.035 ******* 0.0150 3.3V 12.690 0.030 ******* 0.0122 12V1 10.620 0.060 ******* 0.0322 12V2 10.620 0.060 ******* 0.0264 12V3 10.620 0.060 ******* 0.0311 -12V 0.420 0.060 ******* 0.0305 5VSB 2.530 0.040 ******* 0.0084 12V4 10.620 0.060 ******* 0.0281 12V5 10.620 0.060 ******* 0.0306 ================================================================================ STEP.27(UUT Test seq.27) : Noise Test(12V Full Load 264Vac (Load D)) ------ PASS Vin (V)= 264.00 Fin (Hz)= 63.00 Delay Time (ms)= 1000.00 Load Noise Range Noise B.W Name (V) (MHz) ------------- ----------- --------- 5V 0.400 20.00 3.3V 0.400 20.00 12V1 0.400 20.00 12V2 0.400 20.00 12V3 0.400 20.00 -12V 0.400 20.00 5VSB 0.400 20.00 12V4 0.400 20.00 12V5 0.400 20.00 Load Loading Vpp Noise Vpp Noise Vpp Noise Name (A/Ohm/V) Max Min (V) ------------- --------- --------- --------- -------- 5V 0.400 0.035 ******* 0.0103 3.3V 0.610 0.030 ******* 0.0066 12V1 12.600 0.060 ******* 0.0297 12V2 12.600 0.060 ******* 0.0256 12V3 12.600 0.060 ******* 0.0291 -12V 0.200 0.060 ******* 0.0198 5VSB 0.000 0.040 ******* 0.0107 12V4 12.600 0.060 ******* 0.0263 12V5 12.600 0.060 ******* 0.0296 ================================================================================ STEP.28(UUT Test seq.28) : Noise Test(Load 1 (+5V FL) 264Vac) ------------- PASS Vin (V)= 264.00 Fin (Hz)= 63.00 Delay Time (ms)= 1000.00 Load Noise Range Noise B.W Name (V) (MHz) ------------- ----------- --------- 5V 0.400 20.00 3.3V 0.400 20.00 12V1 0.400 20.00 12V2 0.400 20.00 12V3 0.400 20.00 -12V 0.400 20.00 5VSB 0.400 20.00 12V4 0.400 20.00 12V5 0.400 20.00 Load Loading Vpp Noise Vpp Noise Vpp Noise Name (A/Ohm/V) Max Min (V) ------------- --------- --------- --------- -------- 5V 25.000 0.035 ******* 0.0190 3.3V 0.000 0.030 ******* 0.0107 12V1 10.230 0.060 ******* 0.0335 12V2 10.230 0.060 ******* 0.0259 12V3 10.230 0.060 ******* 0.0316 -12V 0.500 0.060 ******* 0.0346 5VSB 3.000 0.040 ******* 0.0093 12V4 10.230 0.060 ******* 0.0286 12V5 10.230 0.060 ******* 0.0302 ================================================================================ STEP.29(UUT Test seq.29) : Noise Test(Load 2 (+3.3V FL) 264Vac) ----------- PASS Vin (V)= 264.00 Fin (Hz)= 63.00 Delay Time (ms)= 1000.00 Load Noise Range Noise B.W Name (V) (MHz) ------------- ----------- --------- 5V 0.400 20.00 3.3V 0.400 20.00 12V1 0.400 20.00 12V2 0.400 20.00 12V3 0.400 20.00 -12V 0.400 20.00 5VSB 0.400 20.00 12V4 0.400 20.00 12V5 0.400 20.00 Load Loading Vpp Noise Vpp Noise Vpp Noise Name (A/Ohm/V) Max Min (V) ------------- --------- --------- --------- -------- 5V 8.500 0.035 ******* 0.0166 3.3V 25.000 0.030 ******* 0.0151 12V1 10.230 0.060 ******* 0.0333 12V2 10.230 0.060 ******* 0.0257 12V3 10.230 0.060 ******* 0.0317 -12V 0.500 0.060 ******* 0.0348 5VSB 3.000 0.040 ******* 0.0083 12V4 10.230 0.060 ******* 0.0285 12V5 10.230 0.060 ******* 0.0304 ================================================================================ STEP.30(UUT Test seq.30) : Noise Test(Load 4 (+5V +3.3V FL, 0A) (Load B) 26 PASS Vin (V)= 264.00 Fin (Hz)= 63.00 Delay Time (ms)= 1000.00 Load Noise Range Noise B.W Name (V) (MHz) ------------- ----------- --------- 5V 0.400 20.00 3.3V 0.400 20.00 12V1 0.400 20.00 12V2 0.400 20.00 12V3 0.400 20.00 -12V 0.400 20.00 5VSB 0.400 20.00 12V4 0.400 20.00 12V5 0.400 20.00 Load Loading Vpp Noise Vpp Noise Vpp Noise Name (A/Ohm/V) Max Min (V) ------------- --------- --------- --------- -------- 5V 12.500 0.035 ******* 0.0133 3.3V 18.940 0.030 ******* 0.0119 12V1 0.000 0.060 ******* 0.0242 12V2 0.000 0.060 ******* 0.0209 12V3 0.000 0.060 ******* 0.0221 -12V 0.000 0.060 ******* 0.0047 5VSB 0.000 0.040 ******* 0.0069 12V4 0.000 0.060 ******* 0.0222 12V5 0.000 0.060 ******* 0.0204 ================================================================================ STEP.31(UUT Test seq.31) : Noise Test(Load 10 (+12V FL, 0A) (Load E) 264Vac PASS Vin (V)= 264.00 Fin (Hz)= 63.00 Delay Time (ms)= 1000.00 Load Noise Range Noise B.W Name (V) (MHz) ------------- ----------- --------- 5V 0.400 20.00 3.3V 0.400 20.00 12V1 0.400 20.00 12V2 0.400 20.00 12V3 0.400 20.00 -12V 0.400 20.00 5VSB 0.400 20.00 12V4 0.400 20.00 12V5 0.400 20.00 Load Loading Vpp Noise Vpp Noise Vpp Noise Name (A/Ohm/V) Max Min (V) ------------- --------- --------- --------- -------- 5V 0.000 0.035 ******* 0.0103 3.3V 0.000 0.030 ******* 0.0069 12V1 12.600 0.060 ******* 0.0299 12V2 12.600 0.060 ******* 0.0254 12V3 12.600 0.060 ******* 0.0297 -12V 0.200 0.060 ******* 0.0202 5VSB 0.000 0.040 ******* 0.0109 12V4 12.600 0.060 ******* 0.0270 12V5 12.600 0.060 ******* 0.0299 ================================================================================ STEP.32(UUT Test seq.32) : Noise Test(Load 11 (+5V +3.3V FL, +12V) (Load C) PASS Vin (V)= 264.00 Fin (Hz)= 63.00 Delay Time (ms)= 1000.00 Load Noise Range Noise B.W Name (V) (MHz) ------------- ----------- --------- 5V 0.400 20.00 3.3V 0.400 20.00 12V1 0.400 20.00 12V2 0.400 20.00 12V3 0.400 20.00 -12V 0.400 20.00 5VSB 0.400 20.00 12V4 0.400 20.00 12V5 0.400 20.00 Load Loading Vpp Noise Vpp Noise Vpp Noise Name (A/Ohm/V) Max Min (V) ------------- --------- --------- --------- -------- 5V 12.500 0.035 ******* 0.0153 3.3V 18.940 0.030 ******* 0.0139 12V1 10.580 0.060 ******* 0.0322 12V2 10.580 0.060 ******* 0.0257 12V3 10.580 0.060 ******* 0.0308 -12V 0.200 0.060 ******* 0.0219 5VSB 0.000 0.040 ******* 0.0116 12V4 10.580 0.060 ******* 0.0280 12V5 10.580 0.060 ******* 0.0302 ================================================================================ STEP.33(UUT Test seq.33) : Sync Dynamic Test_2(15% 50Hz Sync Step at 20% Lo PASS Vin (V)= 115.00 Fin (Hz)= 60.00 Delay time (ms)= 3000.00 UUT Off Time (s)= 0.00 Measurement Time (ms) = 500.00 Duration-1 (ms)= 10.00 Duration-2 (ms)= 10.00 Load Loading-1 Loading-2 Rise Rate Fall Rate Name (A) (A) (A/us) (A/us) ------------- --------- --------- --------- --------- 5V 2.540 6.290 1.0000 1.0000 3.3V 2.540 6.290 1.0000 1.0000 12V1 2.120 4.010 1.0000 1.0000 12V2 2.120 4.010 1.0000 1.0000 12V3 2.120 4.010 1.0000 1.0000 -12V 0.080 0.080 0.1000 0.1000 5VSB 0.510 0.510 0.1000 0.1000 12V4 2.120 4.010 1.0000 1.0000 12V5 2.120 4.010 1.0000 1.0000 Load Vpk Max Vpk Min Vpk High Vpk Low Name (V) (V) (V) (V) ------------- --------- --------- --------- --------- 5V 5.250 4.750 <5.250 >4.750 3.3V 3.498 3.102 <3.498 >3.102 12V1 12.600 11.400 <12.600 >11.400 12V2 12.600 11.400 <12.600 >11.400 12V3 12.600 11.400 <12.600 >11.400 -12V -13.200 -10.800 <-13.200 >-10.800 5VSB 5.250 4.750 <5.250 >4.750 12V4 12.600 11.400 <12.600 >11.400 12V5 12.600 11.400 <12.600 >11.400 ================================================================================ STEP.34(UUT Test seq.34) : Sync Dynamic Test_2(15% 50Hz Sync Step at 20% Lo PASS Vin (V)= 230.00 Fin (Hz)= 50.00 Delay time (ms)= 3000.00 UUT Off Time (s)= 0.00 Measurement Time (ms) = 500.00 Duration-1 (ms)= 10.00 Duration-2 (ms)= 10.00 Load Loading-1 Loading-2 Rise Rate Fall Rate Name (A) (A) (A/us) (A/us) ------------- --------- --------- --------- --------- 5V 2.540 6.290 1.0000 1.0000 3.3V 2.540 6.290 1.0000 1.0000 12V1 2.120 4.010 1.0000 1.0000 12V2 2.120 4.010 1.0000 1.0000 12V3 2.120 4.010 1.0000 1.0000 -12V 0.080 0.080 0.1000 0.1000 5VSB 0.510 0.510 0.1000 0.1000 12V4 2.120 4.010 1.0000 1.0000 12V5 2.120 4.010 1.0000 1.0000 Load Vpk Max Vpk Min Vpk High Vpk Low Name (V) (V) (V) (V) ------------- --------- --------- --------- --------- 5V 5.250 4.750 <5.250 >4.750 3.3V 3.498 3.102 <3.498 >3.102 12V1 12.600 11.400 <12.600 >11.400 12V2 12.600 11.400 <12.600 >11.400 12V3 12.600 11.400 <12.600 >11.400 -12V -13.200 -10.800 <-13.200 >-10.800 5VSB 5.250 4.750 <5.250 >4.750 12V4 12.600 11.400 <12.600 >11.400 12V5 12.600 11.400 <12.600 >11.400 ================================================================================ STEP.35(UUT Test seq.35) : Sync Dynamic Test_2(15% 50Hz Sync Step at 50% Lo PASS Vin (V)= 115.00 Fin (Hz)= 60.00 Delay time (ms)= 3000.00 UUT Off Time (s)= 0.00 Measurement Time (ms) = 500.00 Duration-1 (ms)= 10.00 Duration-2 (ms)= 10.00 Load Loading-1 Loading-2 Rise Rate Fall Rate Name (A) (A) (A/us) (A/us) ------------- --------- --------- --------- --------- 5V 6.340 10.090 1.0000 1.0000 3.3V 6.340 10.090 1.0000 1.0000 12V1 5.310 7.200 1.0000 1.0000 12V2 5.310 7.200 1.0000 1.0000 12V3 5.310 7.200 1.0000 1.0000 -12V 0.210 0.210 0.1000 0.1000 5VSB 1.260 1.260 0.1000 0.1000 12V4 5.310 7.200 1.0000 1.0000 12V5 5.310 7.200 1.0000 1.0000 Load Vpk Max Vpk Min Vpk High Vpk Low Name (V) (V) (V) (V) ------------- --------- --------- --------- --------- 5V 5.250 4.750 <5.250 >4.750 3.3V 3.498 3.102 <3.498 >3.102 12V1 12.600 11.400 <12.600 >11.400 12V2 12.600 11.400 <12.600 >11.400 12V3 12.600 11.400 <12.600 >11.400 -12V -13.200 -10.800 <-13.200 >-10.800 5VSB 5.250 4.750 <5.250 >4.750 12V4 12.600 11.400 <12.600 >11.400 12V5 12.600 11.400 <12.600 >11.400 ================================================================================ STEP.36(UUT Test seq.36) : Sync Dynamic Test_2(15% 50Hz Sync Step at 50% Lo PASS Vin (V)= 230.00 Fin (Hz)= 50.00 Delay time (ms)= 3000.00 UUT Off Time (s)= 0.00 Measurement Time (ms) = 500.00 Duration-1 (ms)= 10.00 Duration-2 (ms)= 10.00 Load Loading-1 Loading-2 Rise Rate Fall Rate Name (A) (A) (A/us) (A/us) ------------- --------- --------- --------- --------- 5V 6.340 10.090 1.0000 1.0000 3.3V 6.340 10.090 1.0000 1.0000 12V1 5.310 7.200 1.0000 1.0000 12V2 5.310 7.200 1.0000 1.0000 12V3 5.310 7.200 1.0000 1.0000 -12V 0.210 0.210 0.1000 0.1000 5VSB 1.260 1.260 0.1000 0.1000 12V4 5.310 7.200 1.0000 1.0000 12V5 5.310 7.200 1.0000 1.0000 Load Vpk Max Vpk Min Vpk High Vpk Low Name (V) (V) (V) (V) ------------- --------- --------- --------- --------- 5V 5.250 4.750 <5.250 >4.750 3.3V 3.498 3.102 <3.498 >3.102 12V1 12.600 11.400 <12.600 >11.400 12V2 12.600 11.400 <12.600 >11.400 12V3 12.600 11.400 <12.600 >11.400 -12V -13.200 -10.800 <-13.200 >-10.800 5VSB 5.250 4.750 <5.250 >4.750 12V4 12.600 11.400 <12.600 >11.400 12V5 12.600 11.400 <12.600 >11.400 ================================================================================ STEP.37(UUT Test seq.37) : Sync Dynamic Test_2(15% 50Hz Sync Step at 85% Lo PASS Vin (V)= 115.00 Fin (Hz)= 60.00 Delay time (ms)= 3000.00 UUT Off Time (s)= 0.00 Measurement Time (ms) = 500.00 Duration-1 (ms)= 10.00 Duration-2 (ms)= 10.00 Load Loading-1 Loading-2 Rise Rate Fall Rate Name (A) (A) (A/us) (A/us) ------------- --------- --------- --------- --------- 5V 8.940 12.690 1.0000 1.0000 3.3V 8.940 12.690 1.0000 1.0000 12V1 8.730 10.620 1.0000 1.0000 12V2 8.730 10.620 1.0000 1.0000 12V3 8.730 10.620 1.0000 1.0000 -12V 0.420 0.420 0.1000 0.1000 5VSB 2.530 2.530 0.1000 0.1000 12V4 8.730 10.620 1.0000 1.0000 12V5 8.730 10.620 1.0000 1.0000 Load Vpk Max Vpk Min Vpk High Vpk Low Name (V) (V) (V) (V) ------------- --------- --------- --------- --------- 5V 5.250 4.750 <5.250 >4.750 3.3V 3.498 3.102 <3.498 >3.102 12V1 12.600 11.400 <12.600 >11.400 12V2 12.600 11.400 <12.600 >11.400 12V3 12.600 11.400 <12.600 >11.400 -12V -13.200 -10.800 <-13.200 >-10.800 5VSB 5.250 4.750 <5.250 >4.750 12V4 12.600 11.400 <12.600 >11.400 12V5 12.600 11.400 <12.600 >11.400 ================================================================================ STEP.38(UUT Test seq.38) : Sync Dynamic Test_2(15% 50Hz Sync Step at 85% Lo PASS Vin (V)= 230.00 Fin (Hz)= 50.00 Delay time (ms)= 3000.00 UUT Off Time (s)= 0.00 Measurement Time (ms) = 500.00 Duration-1 (ms)= 10.00 Duration-2 (ms)= 10.00 Load Loading-1 Loading-2 Rise Rate Fall Rate Name (A) (A) (A/us) (A/us) ------------- --------- --------- --------- --------- 5V 8.940 12.690 1.0000 1.0000 3.3V 8.940 12.690 1.0000 1.0000 12V1 8.730 10.620 1.0000 1.0000 12V2 8.730 10.620 1.0000 1.0000 12V3 8.730 10.620 1.0000 1.0000 -12V 0.420 0.420 0.1000 0.1000 5VSB 2.530 2.530 0.1000 0.1000 12V4 8.730 10.620 1.0000 1.0000 12V5 8.730 10.620 1.0000 1.0000 Load Vpk Max Vpk Min Vpk High Vpk Low Name (V) (V) (V) (V) ------------- --------- --------- --------- --------- 5V 5.250 4.750 <5.250 >4.750 3.3V 3.498 3.102 <3.498 >3.102 12V1 12.600 11.400 <12.600 >11.400 12V2 12.600 11.400 <12.600 >11.400 12V3 12.600 11.400 <12.600 >11.400 -12V -13.200 -10.800 <-13.200 >-10.800 5VSB 5.250 4.750 <5.250 >4.750 12V4 12.600 11.400 <12.600 >11.400 12V5 12.600 11.400 <12.600 >11.400 ================================================================================