                                                  ZyXEL Communications Corp.
                                                     edited by Manfred Recla
                                                              April 09, 1999



   Release Note on ZyXEL's "G3" Modem series (= U-336R/RE, U-336E/S)
   Version 1.17                                       March 23, 1999
   =================================================================



 1.) Fixed modem bugs:
 ---------------------
   .V.13 HDX mode (only support for not V.34 mode)
     Set bit 5 of s44 equal to 1 (ats44.5=1) -> V.13 HDX mode can't work.

   .Leased line mode:
     In sync mode, drop the connection and then change "data format" to
     async, the connection speed is still 28800bps. You have to drop line
     again and then the connection speed will be back 33600bps again.

   .DTE speed:
     .Set s18 equal to an invalid value, the modem will hang.
     .It would appear some garbage after connection in sync or SD mode.
     .When the DTE speed > 230400bps, it can't use Zmodem send file in
      &K0&N0 mode.

   .Remote configuation:
     If you initial remote configuration for the second times, the modem
     will hang.

   .Link Layer:
     There are many retransmissions (the AA led will flash very often) when
     connects at low DCE speed. And it will cause the throughput low.

   .LDL:
    When initial AT&T3 LDL function from RS232 after connect, the remote
    site modem will show 2b/SREJ .

   .Dial backup:
    When two modems connected at 4-wire leased line with dial backup enabled,
    if the answer modem power on without connection at leased line, it can't
    detect ring.

   .*G2:
    It displays the wrong word. When answer site used *G4&k2 command. the
    originate modem will display "correc" after checked password .

   .Ring Detection:
    .If you dial a pulse dial from the attached phone ,sometimes the modem
     will false alarm to ring.
    .Sometimes the modem card on ZyXEL RS-1612 chasis will not detect ring.

   .LCD:
    U336S will not show "System testing" at initialization.

   .V.25bis command:(*I1)
    .The modem will auto answer after first ring even if s0 is not equal to 0 .
    .The modem will produce some garbage at sync mode when the modem rings.
    .Issue "CIC" command will let s0 equal to 2.
    .It will not handshake again after line drop at synchronous leased line
     mode.

   .Speaker:
    .The ringing sound is strange when sync mode (&m1 or &m3).
    .Sometimes the modem will not mute after connection.

   .NMS related bug:
    .The remote management from U336S to U336R via 2nd channel. If you
     transfer file and change the U336R's settings from U336S at the same
     time. The display of setting on U336R is different from U336S (Note:
     If you don't  transfer file, it works fine).
    .The line status report of local is not different from the report of
     remote NMS system.
    .The HS (V34) LED display of remote U336S is not correct on ZyVIEW
     remote control appliation or on rack controller.
    .RTS LED display is not correct on ZyVIEW.
    .Reset from profile to dialup line mode from rack controller at leased
     line mode, it would fail to detect ring.
    .It would get some problem when U336S manage U336S for the second time.
    .The remote management via second channel with Sync mode. If you set
     remote modem U336S panel "Lock" from controller LCD panel remote icon.
     then you set "unlock" from U336S right , left key. The U336R controller
     LCD panel detect "Unlock" will cost long time about 10 mins.
    .When you set global slot and reset profile to factory default from
     controller. It would spend about 8 secs to complete global settings.
    .Can't change the value of S3-register from ZyView or Rack controller.
    .When you reset profile in U336S . The "remote Id" will eliminate and
     you must assign again.

 2.) Fax releated bugs fixed:
 ----------------------------
    .Issue ATD after connection will respond error in some country.
    .Improve the compatibility with Fax machine.
    .Fax Class 1:
     .If "AT+FRH=3" time out, the modem can't accept AT command anymore.
     .The modem can't quickly abort after issue "ATD" command.
    .The modem should respond "OK" instead of "No Carrier", after issue "ATH"
     command.




-----------------------------------------------------------------------------



   Release Note on ZyXEL's "G3" Modem series (= U-336R/RE, U-336E/S)
   Version 1.16                                     December 1, 1998
   =================================================================


 1.) Fixed modem bugs:
 ---------------------
    .Diagonsitic:
        .TxD,RxD LED is not off in synchronous LDL mode.
        .ALB(ST) will abort if the temperature is too high.
        .AT&Tn, if n>=10, modem will not response error.
        .RDL: Sometimes the RDL will fail although the remote side already
              accepts RDL when the data rate >28800 bps.
    .Security:
        .call back (*G4,*G5) doesn't work in V.22 1200 bps.
        .*G2 function call back fail.
    .Link Layer:
        .V.42 compatibility problem with USR X2 modem.
        .V.42bis: Sometimes the modem will reset at high DTE speed and Low
         connection rate.
    .U336R/U336RE
       .Switch leased line to DL from Rack controller, the modem can't detect
        ring.
       .Set the DTE speed to 9600 from Rack controller and then reset from
        factory default the DTE speed can't back to 115200.
    .Physical Layer:
       .Fax mode: Can't connect 9600 bps speed.
       .V23 mode: Can't connect at 2WLL or DL mode.
       .V.22bis: It will appear some garbage right after connection at
        none-error control mode.
       .V.21: When remote side answer the phone quickly, it can't connect.
    .Issue ATZ4 from RS232 will response garbage if DTE speed is not 115200.

 2.) Added new features:
------------------------
    .V.23 4WLL backward channel is replaced by data channel.
    .add DTMF generation function:
     "AT+VTS" command is valid under "AT+FCLASS=8".
    .Formal Release NMS (Network Management System) Function
     (Note: It has better to be used together with ZyViewII Version 1.1 and
            Rack Controller firmware Version "NMSv1.2")

     Remote Management Installation Guide

     Type I : U336R (master) ---> U336S (slave)
      (a) secondary channel
          step 1 : setting
                   U336R                   U336S
                   2nd channel (enable)    2nd channel (enable)
                   Remote ID (master)      Remote ID (slave)
                   Main channel (disable)  Main channel (disable)
          step 2 : get connection
          step 3 : press "R" from LCD pannel of U336R controller
          step 4 : get remote status from LCD pannel
      (b) main channel
          step 1 : setting
                   U336R                   U336S
                   2nd channel (disable)   2nd channel (disable)
                   Remote ID (master)      Remote ID (slave)
                   Main channel (enable)   Main channel (enable)
                                           RDL Request (Granted)
          step 2 : same as above in (a)

      Type II : U336S (master) ---> U336R (slave)
      (a) secondary channel
          step 1 : setting
                   U336R                   U336S
                   2nd channel (enable)    2nd channel (enable)
                   Remote ID (disable)     Remote ID (disable)
                           or (master)
                   Main channel (disable)  Main channel (disable)
          step 2 : get connection
          step 3 : press "R" from LCD pannel of U336S controller
          step 4 : get remote status from LCD pannel

      (b) Main channel
          step 1 : setting
                   U336R                   U336S
                   2nd channel (disable)   2nd channel (disable)
                   Remote ID (master)      Remote ID (disable)
                          or (disable)
                   Main channel (enable)   Main channel (enable)
                   RDL Request (Granted)   RDL Request (Granted)

          step 2 : same as above in (a)

     Type III : U336S  <---> U336S
      (a) secondary channel
          step 1 : setting
                   U336S                   U336S
                   2nd channel(enable)     2nd channel(enable)
                   Remote ID (disable)     Remote ID (disable)
                   Main channel(disable)   Main channel(disable)
          step 2-4 : Same as above in Type II.

      (b) Main channel
          step 1 : setting
                   U336S                   U336S
                   2nd channel(disable)    2nd channel(disable)
                   Remote ID (disable)     Remote ID (disable)
                   Main channel(enable)    Main channel(enable)
          step 2 : same as above in (a)



-----------------------------------------------------------------------------



   Release Note on ZyXEL's "G3" Modem series (= U-336R/RE, U-336E/S)
   Version 1.15                                     December 1, 1998
   =================================================================

      v1.15 was not formally released
      modifications are merged above into release notes for v1.16 !


-----------------------------------------------------------------------------




   Release Note on ZyXEL's "G3" Modem series (= U-336R/RE, U-336E/S)
   Version 1.14                                     August 14, 1998
   =================================================================


 1. Fixed modem bugs:
 --------------------
    .WinFax 8.0x compatibility problem:
     Can't send fax by using class 2 command.
    .RDL problem:
     Sync mode can't transfer anymore after RDL+ST.
    .Can't send file when DCE speed is greater than 115200 bps and DCE speed
     is lower than 9600 bps in async error control mode.
    .V.25bis compatibility problem with IBM router.
    .Improve NMS stability.

 2. Added new features:
 ----------------------
    .Added eight non-changeable profiles (5-14).
     These profiles won't be active profiles. If you want them to become an
     active profile, you must load it first and then save it to profile 0 to
     3. You can load these profiles by ATZn (n=5-14) or by LCD front panel in
     the screen "RESET" of U336S.

     for example use the command sequence:  ATZ6&W0Z0

     The detail settings are as followings:
      profile 5 :  TAIWAN STOCK MARKET: &D0&L1&K0&H0S35=34S18=9S57.1=1*I2E0Q1
      profile 6 :  ASYNC-2L + &D0&K0&H0E0Q1
      profile 7 :  SYNC-2L  + &D0&K0&H0E0Q1
      profile 8 :  ASYNC-4L + &D0&K0&H0E0Q1
      profile 9 :  SYNC-4L  + &D0&K0&H0E0Q1

      The following profiles are for NMS (Network Management Service) only
      They are not valid in U336RE or U336E !
      ---------------------------------------------------------------------
      profile 10:
      ASYNC-2L-2ndCH-RTOS       ;U336S=REMOTE ID SLAVE, RDL GRANTED,
                                ;MAIN CHANNEL ENABLED ,2ND CHANNEL ENABLED

                                ;U336R=REMOTE ID MASTER,MAINCH ENABLE,2NDCH
                                ;ENABLE
      profile 11:
      ASYNC-2L-MainCH-RTOS      ;U336S=REMOTE ID SLAVE,RDL GRANT,MAINCH ENABLE
                                ,2NDCH DISABLE
                                ;U336R=REMOTE ID MASTER,MAINCH ENABLE,2NDCH
                                DISABLE
      profile 12:
      ASYNC-4L-2ndCH-RTOS       ;U336S=REMOTE ID SLAVE,RDL GRANT,MAINCH ENABLE
                                ,2NDCH ENABLE
                                ;U336R=REMOTE ID MASTER,MAINCH ENABLE ,2NDCH
                                 ENABLE
      profile 13:
      ASYNC-4L-MainCH-RTOS      ;U336S=REMOTE ID SLAVE,RDL GRANT, MainCH
                                 ENABLE, 2ndCH DISABLE
                                ;U336R=REMOTE ID MASTER,MainCH ENABLE,2ndCH
                                DISABLE
      profile 14:
      ASYNC-DIAL-NMS-STOR       ;U336S=REMOTE ID DISABLE, RDL GRANT, MainCH
                                 ENABLE, 2ndCH ENABLE

    .extend valid DTE speed on "DTE ASYNC SPEED" screen.
    .if set &S1 and s55.7=1
     Modem will turn on DSR after CD is on.
     (this solves the compatibility problem with 3COM routers).




----------------------------------------------------------------------------



   Release Note on ZyXEL's "G3" Modem series (= U-336R/RE, U-336E/S)
   Version 1.13                                     August 14, 1998
   =================================================================
   not officially released because "13" is an "unlucky" number :-)



----------------------------------------------------------------------------




   Release Note on ZyXEL's "G3" Modem series (= U-336R/RE, U-336E/S)
   Version 1.12                                        June 25, 1998
   =================================================================


 1. Fix modem bugs:
 ------------------
    1)  Default power is always -11 dBm after hardware reset .
    2)  LCD operation for U336S:
        .Cursor is wrong positioned on LCD when entering network address
         from U-336S front pannel.
    3)  V.34 sync mode:
        .The modem will initiate retrain immediately after connection when
         the clock soure is from external device if the external clock
         is not applied to the modem during handshaking.
        .The internal processing delay is shortened.
    4)  When the remote side requests the additional power, the Tx Power
        level reported by the modem is not correct.
    5)  The simulated 2 wired lease line  over dial up line can't connect in
        Russia.
    6)  Fax mode:
        .The connect speed is not correct for "AT+FDCC=1,2" or "AT+FDCC=1,4".
    7)  Sync V.25bis command bugs
        .The first command ack will missed out after power on or V.25bis
         setting.
        .S41.1=1 fail for mark idle.
    8)  Can't sense abnormal carrier drop in 15 sec at V.34 mode.
    9)  LDL and RDL related problem:
        .LDL may fail if there is no DTR exists.
        .RDL false alarm to End testing when connect speed >28800 bps.
        .Can't initial RDL at low data rate.
    10) The connect message is always "V.33 14400" when s52=96 in non V.34
        mode.
    11) It would initial retrain or FRN in one day when bk-bk connection
        in V34 mode.
    12) Ring detection problem in France.
    13) It would initial retrain or FRN frequently when connect with Ascend
        Max terminal server (if it offers Rockwell K56.flex protocol)
    14) Can't connect with V.90 modem by using V.34.
    15) Fax mode:
        . Sometimes V.34 LED will not turn off in Fax mode.
        . Fax compatibility problem with software HylaFax when sending Fax.

 2. Add new feature:
 -------------------
    1) for U336S:
        .add phone number option for store and view phone number in data
         state or in leased line mode.




-----------------------------------------------------------------------------




   Release Note on ZyXEL's "G3" Modem series (= U-336R/RE, U-336E/S)
   Version 1.11                                       April 07, 1998
   =================================================================


1. Fix modem bugs:
------------------
    1) AT command bug:
       .ATZ4S0M0N0=1 should response error.
       .ATSr=n. When n is greater than 256. The modem should response error.
       .If you issue command 'ATM0L0',the modem will excute 'ATDL' command.
       .If you issue command'ATO26',the modem will excute 'ATD26'command.
       .The report for 'AT+FCLASS=?' contains voice mode.
        (But modem can accept '+FCLASS=8' setting for DTMF detection)
       .ATDxxxx@ will not report 'No Answer' when the remote side doesn't
        answer the call.
       .The AT comand string will not be exactly when the string length
        exceeds 14 characters while the DTE speed is 460800 bps.
    2) Multi-Auto mode:
       .If the quality action setting of the modem is not 'adaptive rate'.
        The modem always connects at 33600 speed.
    3) .The modem can't send NULL character in data state.
    4) .The receive level reported by the modem is not correct.
    5) V.32 related mode (V.32,V.32bis,ZyCelluar,Zy19k2,Zy16k8)
       .The second retrain will force modem to drop one speed.
       .The counter of retrain request and retrain granted are not correct.
    6) .The waiting time is too long to initiate security call back.
    7) .Dial backup function will fail when unplug U336R modem card and plug
        in again during dial back up mode.
    8) .The modem can't work in N71 asynchronous data format.
    9) ZyCelluar mode:
       .The modem may get carrier lost when typing 'ATO1' to initiate a
        retrain.
    10) Sync (or Sync data) mode:
        .The internal processing delay is shortened at V.34 mode.
    11).Modem would get carrier lost when connects with K56Flex modem.
    12).Improve V.34 performance over bad line.
    13).The modem is apt to initiate FRNs or retrains in V.34 2400 mode.

 2. Add new feature:
 -------------------
    1). Set s58.4=1 will give up FSK mode (V.21, B103, V.23) in Multi-Auto
        mode. Using this bit can avoid the modem connects as FSK mode.
    2). Set s12.7=1 will enable pseudo CD function in sync mode.
    3). U336S LCD operation:
        .Add PANEL OPTION which contains
         a).PANEL LOCK (This option is moved from MODEM OPTION)
         b).LCD LIGHTENING (This option is moved from TERMINAL OPTION)
    4). Remote management.
        U336S  <---> U336S
        (a) Secondary channel
            step 1 : setting
                      U336S                   U336S
                      2nd channel(enable)     2nd channel(enable)
                      Remote ID (disable)     Remote ID (disable)
                      Main channel(disable)   Main channel(disable)
            step 2 : get connection
            step 3 : press "R" from LCD pannel of U336S.
            step 4 : get remote status from LCD pannel
        (b) Main channel
            step 1 : setting
                     U336S                   U336S
                     2nd channel(disable)    2nd channel(disable)
                     Remote ID (disable)     Remote ID (disable)
                     Main channel(enable)    Main channel(enable)
            step 2 : same as above in (a)
        Note: 1. The secondary channel uses V.34 200 bps AUX channel. It can
                 only be established in V.34 mode.
              2. The main channel uses the whole data bandwidth. The modem
                 can't transmit or recieve data while the main channel has
                 been established.

 3. Known bug:
 -------------
     The modem is apt to initiate retrains or FRNs when connects with
     K56Flex modems.



-----------------------------------------------------------------------------




   Release Note on ZyXEL's "G3" Modem series (= U-336R/RE, U-336E/S)
   Version 1.10                                    January 22, 1998
   =================================================================


 1. Fix modem bugs:
 ------------------
    1) Performance improvement:
       .The BER (= bit error rate) of V.34 synchronous external clock mode
        under flat channel is high.
       .Modem can initialize FRN one time only in V.32bis mode while the
        channel quality is degraded.
       .*Q3 function doesn't work in non-V34 mode.
    2) U-336S LCD control panel related operation:
       .Press 'UP' arrow key twice will cause malfunction of LCD operation
        when the modem stays at leased line handshaking state.
       .The Tx power reported on LCD display is not correct when transmitted
        power is less than -10 dBm.
       .Sometimes the LCD of modem  can't show 'LDL(ST)' and 'RDL(ST)' after
        doing 'LDL' or 'RDL' test.
    3) Multi-Auto:
       .The modem will reset when the DTE speed of the modem is less or equal
        to 4800 bps and handshake with a V.22bis modem.
       .Sometimes the modem will produce garbages during handshaking when
        connect with a V.22bis modem.
       .Can't connect with non-V34 modem in sync mode.
    4) .The connect speed will show twice in the connect message when the
        setting is X6 or X7.
    5).The EDR function doesn't work.
    6).The ATI12 report contains some spelling errors.
    7).Sometimes the command 'AT&fe0v0' will response "OK" instead of "0".
    8).Firstly, set the terminal with N71 async format and issue 'at&w0z0'.
       Then set the terminal back to N81 async format and issue 'atz', the
       modem will produce garbage.
    9).Compatibility problem
       .Can't handshake with old Motorola modem.
       .Can't handshake with NEC 56K modem, Dynalink 56K modem.
       .Answer mode connection problem when setting s0=1 due to central
        office delay.
    10).RDL test function:
        .modem can't initial RDL test from RS232 pin 18 and pin 21
        .The throughput of the remote side (LDL) is not zero.
        .The DTR and RTS signal is not ignored by the remote side(LDL)
    11).ATI0 report contains "NULL" character.
    12).AT#REV=? will not response error.
       .AT#CLS=? will not response error.(Can't be detected by WinFax 8.0)
    13).The modem will reset itself while doing remote configuration by LCD
        panel.
    14).The RI LED is off when s0 is not equal to 0 .
    15).V.34
       If the remote side is in symmetric mode and the local side is in
       asymmetric mode, the modem will keep fall forward FRN endlessly if the
       local connection condition is better than remote side.
    16).Improve the performance of V.34 mode on bad line
       .Correct the power drop problem of V.34 mode
    17). The transmit level of V.22bis Gaurd tone is not correct.

 2. Add new features:
---------------------
    1). AT*Pn command:
       .Extend the valid range of n from 15 to 31. (It means the transmit
        power is ranging from 0 to -31 dBm)
    2). For U336S:
       .Initial test function from LCD will clamp RS232 signal RxD.
       .Add remote control menu tree
    3). Add clear down procedure in  V.32bis mode.

 3. Known Bugs:
----------------
    In V.34 mode the 2400 bps connection is unstable and is apt to do FRN
    or retrain.




-----------------------------------------------------------------------------



   Release Note on ZyXEL's "G3" Modem series (= U-336R/RE, U-336E/S)
   Version 1.09                                    November 11, 1997
   =================================================================


 1. Fix modem bugs:
 --------------------
    1) Compatbility:
       .Compatibility problem with K56Flex.
       .Cannot connect with RockWell by using V.34 3429 baud.
       .Cannot answer second call by using ZFAX.
       .Cannot do RDL testing with CODEX modem.
       .Support 'AT+fclass=Z' command in the U-336 series modem.
       .Modem will connect as V.32bis in multi-auto mode while the remote
        site is a V.34 modem.
    2) Lesead line operation:
       .2WLL/4WLL keep in retrain state very easily when "Data format"
        ="Sync data".
       .The dialing procedure cannot be aborted manually in dial backup
        application.
       .Fail to do dial up connection while the U-336R modem is unplugged
        from the RS-1612 chassis and be plugged again in dial backup
        application.
       .Fail to do carrier lost detection in non-error control leased line
        connection.
       .The transmit power is incorrect in V.34 handshaking state.
       .When the dial back up mode is forced to be terminated, The modem
        can't go back to leased line mode.
       .Can't be abort before data state in V.34 mode.
    3) RS-1612 related issue:
       .NEC and FEC reported from rack controller or LCD screen is always
        zero.
       .Cannot use the LCD control panel of RS-1612 to initate the RDL
        testing.
       .The leased line operation of U-336R/RE modem will be interrupted
        and be changed as dial-up line setting while doing global "ALB+ST"
        then "END TESTING" from the LCD control panel of RS-1612 rack system.
       .The S/N report on RS-1612 is not correct.
    4) Diagnostic features
       .Fail to do RDL and LDL testing.
       .Fail to do RDL in synchronous mode.
       .Modem will hang in an unknown state while doing ALB, LDL then ALB
       .The RS-232 status and LED indicators are not obeyed the ITU-V.54
        standard when doing RDL or LDL testing.
    5) Performance improvement:
       .There are error happened by using V.34 3429 baud in synchronous mode
        BER testing when the channel spectrum is flat and the SNR is high.
       .Endless retrain.
       .The BER is 10e-1 under V.34 16800.
    6) AT command and response:
       .Inactive timer s50 is useless.
       .The ORG LED is turned on while the "ATS0=1" command is entered in
        dial-up line application.
       .Fail to using the on to off transition of DTR to do dialing while the
        "AT&M1&D1*D1S48.4=1" or "AT&M2&D1*D1S48.4=1" command is entered.
    7) U-336S LCD control panel related operation:
       .Cannot do semi-auto dial backup while the content of register s44=4
       .The RTS and CTS status showed on LCD display screen and LED
        indicators are not consistent.
       .There are garbage displayed on the LCD screen when the right arrow
        key is pressed in four wire leased line answering mode.
       .LCD display can't change connect rate message after FRN or retrain.
    8) Russia special features:
       .Cannot enter "AT+FRH" command in Russian CND mode.
       .Fail to detect busy tone in Russia.
       .The default transmision power changes to -9 dbm.
    9) Fax :
       .The reponse of +FTSI ,+FCSI ... command lacks double quote mark.
    10) Can't transmit file by using V.34 3429 baud 21600 bps link speed.
    11) Initial reset from profile on LCD pannel when modem in ALB mode.
    12) False connect at V.22 1200.
    13) Fail to connect at V.34 4800 and V.34 2400.
    14) Issue AT&F while modem initial V.34 clear down will cause modem to
        hang.
    15) CD pulse off bug when S42.7=1.
    16) Remote configuration:
        AT*Wab fail. The remote modem can't reset from profile b.

 2. Add new features:
 --------------------
    1) AT command and response:
       Add a new ATI13 command: Issue "ATI13" command in V.34 escape state,
       modem will plot channel spectrum probed in V.34 phase 2.
    2) U-336S LCD control panel related operation:
       .Control the LCD back light with the following ways:
        Leased line mode:
        a. The back light is always turned on when the connection is dropped.
        b. The back light will be turned off after on line 15 sec.
        c. The back light will be turned on immediately while any panel key
           is pressed.
        Dial up line mode:
        a. The back light will glitter when the ring is coming.
        b. The back light will glitter in handshaking state.
        c. The back light will be turned off after on line 15 sec.
        d. The back light will be turned on when modem hangs up.
        e. The back light will be turned off after the modem is idle 1 min.
        f. The back light will be turned on immediately when any panel
           key is pressed.
        This function can be disbled by LCD panel or by setting s61.1=1.
        (default is on).
    3) Data state status display screen:
       Data state status displayed screen will be changed to
  1.Ŀ2.Ŀ3.Ŀ4.Ŀ
 >M   TR     RR     LL/DL>SNR=  CLC=>RTG=  RTR= >LM/SREJ BLS=>Ŀ
 ĴH>> TXTGHP RXTGHP AS/SY<ĴTXL=  RXL=<ĴFRG=  FRR= <ĴBLR=    FRE=<Ŀ
          
 10   9.    8.     7.     6.Ŀ5 Ŀ
 >Graph>TXC=RXC=>TSH= RSH= >NLE= NLD=>PHJ= FRO=>NEC=RTD=ٳ
 Ĵ     <ĴTXB=RXB=<ĴTFI= RTFI=<ĴTRE= CND=<ĴEDL      <ĴFEC=EFO=
                               
       Screen 7,8,9,10 will only be shown in V.34 mode.
       The explanation:
            M:Modulation Mode               TR:Transmit Rate
           RR:Receive Rate                  DL:Dial Up Line
           LL:2LO,2LA,4LO,4LA (2/4: 2 wired or 4 wired leased line
              O:originate mode , A:answer mode)
       TXTGHP:Transmit Throughput
       RXTGHP:Receive Throughput            AS:Async Mode
           SY:Sync Mode                    SNR:Signal to Nosise Ratio
          RXL:Rx Signal Level              PHJ:Phase Jitter
          FTO:Frequecy Offset              RTG:Retrain Granted Count
          FRR:FRN Request                  BLR:Block Retransmitted
          FRE:FCS Error                    TXC:Tx Carrier
          RXC:Rx Carrier                   TXB:Tx Baud Rate
          RXB:Rx Baud Rate                 BLS:Max Block Size
          RTR:Retrain Request Counts       EDL:Echo Delay(rts in baud)
          CLC:Carrier Lost Counts          NLE:Nonlinear Encoder
          NLD:Nonlinear Decoder            TRE:Trellis Encoder
          CND:Convolutional Decoder        TSH:Tx Shapping
          RSH:Rx Shapping                  TFI:Tx Filter Index
         RTFI:Remote Tx Filter Index       NEC:Near End Echo
          RTD:Round Trip Delay             FEC:Far End Echo
          EFO:Frequency Offset              LM:Link Layer Mode
         SREJ:Selective Reject             TXL:Tx Power
         Graph: show the line spectrum probed by V.34 phase 2.
                    LCD  SCREEN ( 20(BLOCKS)*2(ROWS) )
         (db) 0 Ŀ Ŀ
             -2 Ĵ   
             -4 Ĵ   
             -6 Ĵ   
             -8 Ĵ    ROW 1
            -10 Ĵ   
            -12 Ĵ   
            -14 Ĵ   
                 
            -16 ĿĿ
            -18 Ĵ   
            -20 Ĵ   
            -22 Ĵ   
            -24 Ĵ    ROW 2
            -26 Ĵ   
            -28 Ĵ   
            -30 Ĵ   
                 
                 0 0 0 0 0 1 1 1 1 1 2 2 2 2 2 3 3 3 3 3 (Frequency)
                 1 3 4 6 7 0 3 5 6 9 1 2 5 7 8 0 1 3 4 7
                 5 0 5 0 5 5 5 0 5 5 0 5 5 0 5 0 5 0 5 5
                 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
            This function displays 20 tones from 150hz to 3750hz except for
            900hz,1200hz,1800hz,2400hz which are not transmitted practically.
    4) Adjust transmit power:
       When the bit 3 of register s35 equals one, the transmision power will
       be added 16 dB attenuation instead of 12 dB attenuation as described
       in the user's manual.
    5) When s65.3=1 is entered, modem will report ring at off to on
       transition of ring signal. ISP can use this feature to answer the
       incoming call more quickly.


-----------------------------------------------------------------------------




   Release Note on ZyXEL's "G3" Modem series (= U-336R/RE, U-336E/S)
   Version 1.08                                        June 20, 1997
   =================================================================


 1. Fix modem bugs :
 -------------------
    * Rx level reported by modem is not correct.
    * Sometimes modem sends false alarm to ring immediately after local
      hangup.
    * Pressing O/A button could turn off OH led.
    * Can't do V.54 test fron RS1612 LCD panel.
    * Modem will auto answer even when DTR signal is off.
    * AT&D3 does not work properly.
    * If you type "ATRU", the modem will not response error but enter to
      kernel mode instead.
    * When the DTE speed is 230400, it can't accept any AT command.
    * Inactivity timer:
      If inactivity timer (set by s50) becomes valid, the modem will not
      send the disconnect frame to the remote modem.
    * Auto answer:
      If it sets s0>255, the modem will answer immediately after the
      first ring.
    * Synchronous mode:
      modem will fail to auto answer after 3 hours.
    * Dial backup mode:
      It can switch to dial up line when leased line fails. But it can't
      switch back to leased line again.
    * U-336S model:
      - RDL or RDL+ST mode:
        If forcing the RDL or RDL+ST tests from the LCD panel and if the
        remote modem denies it, it will cause hardware reset.
      - If the line drops under abnormal condition, it will cause the modem
        to reset or hang.
    * Leased line mode:
      - If type any error AT command (such as "ATU") in handshaking state,
        then the modem will always reponse error after this command even
        if you type any valid AT command.
      - Sometimes it can't sense carrier drop in V.34 mode. When this
        happens the SQ led glitters quickly.

 2. Add new feature:
 --------------------
    * DTMF detection:
      if set "AT+FCLASS=8" it can detect DTMF tone in anwser mode.
    * Leased line mode:
      Set s57.1=1 can send 2100 Hz answer tone in V.32bis answer mode.
    * Set s58.3=1 can turn off Plug&Play function for Microsoft Windows95.




----------------------------------------------------------------------------




   Release Note on ZyXEL's "G3" Modem series (= U-336R/RE, U-336E/S)
   Version 1.07                                        June 20, 1997
   =================================================================
   was not officially released !



----------------------------------------------------------------------------




   Release Note on ZyXEL's "G3" Modem series (= U-336R/RE, U-336E/S)
   Version 1.06                                         May 06, 1997
   =================================================================


 1. Fix modem bugs:
 ------------------
    * MNP mode:
      - Modem can't connect with GVC336 with MNP4 or MNP5 in call mode.
    * V.34 mode:
      - Modem can't connect with Rockwell based modem at 2400 bps.
      - FRN occurs too frequently.
      - Sometimes SQ led will be off after on line.
    * leased line mode:
      - Leased line mode on line will be dropped and never connected again
        after issuing hangup command.
      - The "LL" led should be on when the 2LL or 4LL mode is selected in
        U-336R model, but it does not.
      - The leased line mode will not be activated after issuing at&l1&wz
        or at&l2&wz.
      - Can't change answer/orignate state from O/A button.
    * U-336S model:
      - The network address menu will show a lot of garbage characters after
        you press keypad from terminal option to network address option menu.
      - It can not abort dialing procedure by pressing any keypad if you dial a
        phone number from front panel "D" keypad. Besides, it will show a lot
        of garbage from LCD during trying to abort dialing procedure.
      - The "D" of "D R O A" menu dialing procedure is not available if the
        phone number is empty. After that we try to enter a phone number it
        is not able to dial as well.
      - Can't change line type from LCD panel during leased line connection.
      - Modem generate ring tone after reset profile from LCD panel.
      - Modem will hang after using the LCD panel "reset profile" function,
        The LCD will display "disconnection ..." in the above operation.
      - Press the "right" arrow key continously, the cursor of LCD will
        be located in the upper row and then the display of LCD is crashed.




----------------------------------------------------------------------------



   Release Note on ZyXEL's "G3" Modem series (= U-336R/RE, U-336E/S)
   Version 1.05                                       April 05, 1997
   =================================================================


 1. Changed the model names:
 ---------------------------
    The model name was changed now from "U-288RE" to "U-336RE".
    The old hardware of "U-288RE" still can be updated by using the
    firmware of "U-336RE".

 2. Fixed modem bugs :
 ---------------------
    * answer mode:
      Modem will drop the first connection after power on.
    * leased line mode:
      When the modem powers on and uses leased line as default, it would stop
      handshaking after a few minutes if the remote doesn't reponse.
    * V.34 mode:
      Endless retrain with busy tone while connecting at V.34 mode.
    * Multi-Auto mode:
      In answer mode it can't handshake with V.22Bis.



 ---------------------------------------------------------------------------



   Release Note on ZyXEL's "G3" Modem series (= U-288R/RE, U-336E/S)
   Version 1.02                                   February 03, 1997
   =================================================================


 1. Fix modem bugs :
 -------------------
    * Remote digital loop back may  fail for U-336S model:
      If we initiate RDL or RDLST from the LCD panel, it will fail .
    * leased line mode:
      When the line is broken under abnormal condition after a long period
      of time the modem may fail to restart handshaking.
    * command ATI0 response:
      The modem responses "2864" in old version.In new version, it will
      response according to different modem type:
         U-288RE will response "33601"
         U-336R  will response "33602"
         U-336S  will response "33603"
         U-336E  will response "33604"
    * In testing mode, the modem will not set pin 25 of RS232 active.
    * MNP4,MNP5 mode:
      Sometimes it can't send or receive data in MNP4,MNP5 mode.
    * V.32bis and ZyX-19k2 mode:
      If the initial setting contains "Q2&K3" and it connects by ZyX-19k2
      or V.32bis mode, the modem will hang after transmit a few characters.

 2. Change the modem factory default settings:
 ---------------------------------------------
    S6 is changed to 10 for Russia.
    S7 is changed to 45 for Taiwan (rack).

 3. Improve performance:
 -----------------------
    * Improve V.34 performance.

 4. Known Bug:
 -------------
    * Software flow control problem:
      The modem will lose data in software flow control mode at high
      connect speed.
    * AT&Wab, Remote write profile functuion error. Remote can't reset from
      profile b.



---------------------------------------------------------------------------




   Release Note on ZyXEL's "G3" Modem series (= U-288R/RE, U-336E/S)
   Version 1.01                                     January 16, 1997
   =================================================================


 1. Add new features:
 --------------------
    * V.34bis 33600 bps, 31200 bps.

 2. Fix modem bugs :
 -------------------
    * V.32bis mode connection:
      Sometimes it can't sense the abnormal carrier drops.
    * Special dialing feature:
      Modem does not finish dialing of numbers specified after P modifier
      and hangs for a time specified in S7 register. For example when
      "ATDT9WP8W10-886-3-578-7045" is entered, modem will report "NO CARRIER"
    * Ring false alarm:
      When pulse dial  by the telephone set connected to modem, the modem
      will report ring.
    * Synchronous mode: (&M3)
      The modem will not give the answer tone when auto answer.
    * Compatibility:
      .Multi-Auto connection:
       The modem can't connect with Motorola Power 288 V.32bis mode .
      .Fail to connect at error control mode:
       Sometimes the modem will connect at none error control mode with
       Rockwell chip set based modem.

 3. Improve performance:
 -----------------------
    * Improve V.34 performance.
    * Improve answer tone detection sensitivity.
    * Improve the modem realibity.

 4. Known Bugs:
 -------------
    * Software flow control problem:
      The modem will lose data in software flow control mode at high connect
      speed.
    * AT&Wab, Remote write profile functuion error. Remote can't reset from
      profile b.

