Release Notes for ProLiant Support Pack for Red Hat Enterprise Linux 3, v7.11 ******************************** aic7xxx-6.3.2-rhel3.i686.rpm - HP ProLiant 64-Bit/66-Mhz Dual Channel Wide Ultra3 SCSI Controller Driver for Red Hat Enterprise Linux 3, v6.3.2-1 Enhancements Initial release. ******************************** net-snmp-cmaX-5.1-83.rhel3.i386.rpm - A Collection of SNMP Protocol Tools from Net-SNMP for Red Hat Enterprise Linux 3 (x86), v5.1-83 Enhancements Initial release of the Net-SNMP package with CMAx extensions from HP. ******************************** net-snmp-cmaX-devel-5.1-83.rhel3.i386.rpm - A Collection of SNMP Protocol Tools from Net-SNMP for Red Hat Enterprise Linux 3 (x86), v5.1-83 Enhancements Initial release of the Net-SNMP package with CMAx extensions from HP. ******************************** net-snmp-cmaX-perl-5.1-83.rhel3.i386.rpm - A Collection of SNMP Protocol Tools from Net-SNMP for Red Hat Enterprise Linux 3 (x86), v5.1-83 Enhancements Initial release of the Net-SNMP package with CMAx extensions from HP. ******************************** net-snmp-cmaX-utils-5.1-83.rhel3.i386.rpm - A Collection of SNMP Protocol Tools from Net-SNMP for Red Hat Enterprise Linux 3 (x86), v5.1-83 Enhancements Initial release of the Net-SNMP package with CMAx extensions from HP. ******************************** net-snmp-cmaX-5.1-83.rhel3.x86_64.rpm - A Collection of SNMP Protocol Tools from Net-SNMP for Red Hat Enterprise Linux 3 (AMD64/EM64T), v5.1-83 Enhancements Initial release of the Net-SNMP package with CMAx extensions from HP. ******************************** net-snmp-cmaX-devel-5.1-83.rhel3.x86_64.rpm - A Collection of SNMP Protocol Tools from Net-SNMP for Red Hat Enterprise Linux 3 (AMD64/EM64T), v5.1-83 Enhancements Initial release of the Net-SNMP package with CMAx extensions from HP. ******************************** net-snmp-cmaX-perl-5.1-83.rhel3.x86_64.rpm - A Collection of SNMP Protocol Tools from Net-SNMP for Red Hat Enterprise Linux 3 (AMD64/EM64T), v5.1-83 Enhancements Initial release of the Net-SNMP package with CMAx extensions from HP. ******************************** net-snmp-cmaX-utils-5.1-83.rhel3.x86_64.rpm - A Collection of SNMP Protocol Tools from Net-SNMP for Red Hat Enterprise Linux 3 (AMD64/EM64T), v5.1-83 Enhancements Initial release of the Net-SNMP package with CMAx extensions from HP. ******************************** hprsm-7.1.1-87.rhel3.i386.rpm - HP Lights-Out Drivers and Agents for Red Hat Enterprise Linux 3, v7.1.1-87 Fixes Resolved an issue that did not allow the rebuild script to work properly. Enhancements Added functionality in the hpasm installer to provide customer choice to not install and/or load the hprsm driver. Added support for the 2.6 kernel. ******************************** hpasm-7.1.1-87.rhel3.i386.rpm - HP Server Management Application and Agents for Red Hat Enterprise Linux 3, v7.1.1-87 Enhancements The previous health driver has been converted into a user space health application. No more tainted kernel messages due to the health driver not being GPL. No more kernel source dependence for health recompiles No kernel version dependence NOTE: The hprsm package is still a set of drivers (and agents) and thus will produce the tainted kernel message as well as remaining kernel dependent. Added the storage agent (cmastor) into the hpasm rpm package. Previously, the storage agent was a separate rpm package. The user can choose not to install the storage agent (or other agents) during the hpasm package installation. Added support for Net-SNMP with HP Extensions. ******************************** hpasm-7.1.1-87.rhel3.x86_64.rpm - HP Server Management Application and Agents for Red Hat Enterprise Linux 3 (AMD64/EM64T), v7.1.1-87 Enhancements The previous health driver has been converted into a user space health application. No more tainted kernel messages due to the health driver not being GPL. No more kernel source dependence for health recompiles. No kernel version dependence. NOTE: The hprsm package is still a set of drivers (and agents) and thus will produce the tainted kernel message as well as remaining kernel dependent. Added the storage agent (cmastor) into the hpasm rpm package. Previously, the storage agent was a separate rpm package. The user can choose not to install the storage agent (or other agents) during the hpasm package installation. Added support for Net-SNMP with HP Extensions. Added support for X86_64 bit Linux Operating systems. Intel EM64T AMD64 ******************************** hprsm-7.1.1-87.rhel3.amd64.rpm - HP Lights-Out Drivers and Agents for Red Hat Enterprise Linux 3 (AMD64/EM64T), v7.1.1-87 Fixes Resolved an issue that did not allow the rebuild script to work properly. Enhancements Added support for X86_64 bit Linux Operating systems: Intel EM64T AMD64 Added functionality in the hpasm installer to provide customer choice to not install and/or load the hprsm driver. Added support for the 2.6 kernel. ******************************** hprsm-7.1.1-87.rhel3.em64t.rpm - HP Lights-Out Drivers and Agents for Red Hat Enterprise Linux 3 (AMD64/EM64T), v7.1.1-87 Fixes Resolved an issue that did not allow the rebuild script to work properly. Enhancements Added support for X86_64 bit Linux Operating systems: Intel EM64T AMD64 Added functionality in the hpasm installer to provide customer choice to not install and/or load the hprsm driver. Added support for the 2.6 kernel. ******************************** cpq_cciss-2.4.50-26.rhel3.i686.rpm - ProLiant Linux driver (x86) for Smart Array 6i, 64xx, 5i, 5300 Series controllers for Red Hat Enterprise Linux 3(x86), v2.4.50-26 Fixes Resolved the following: rpm install script to avoid making a new initrd when the new drive is found to be the same as the existing one. bcm5700 6.2.17a fails to load on base SUSE Linux Enterprise Server 7 kernel. CPQ_CISS v.2.4.48-4 causes Boot menu to default to HP-2.4.7-4GB but kernel is actually 2.4.64GB-SMP. Default initrd incorrect should be SMP/enterprise but is set to UP. Issue where drivers where not being installed properly on Red Hat Enterprise Linux 3 systems. Uninstall issue with UnitedLinux and Red Hat Enterprise Linux 2.1. GRUB naming issue with UnitedLinux. Install script to allow rpm to build an initrd for smp or bigmem kernels even if the hardware is not smp or bigmem. Install issue to allow an initial ram disk to be built for newly installed binary errata kernels in the situation where the hardware is not supported by the driver found in the kernel. Updated the following: Variable type to cover cases when the logical volume size is >1TB. Enabled pre-fetch in the SCSI core for Smart Array for x86 architecture only. Required for firmware >= 1.86. Driver backup directory to /usr/src/HP/driver_backup. The default prefix for the storage rpm to /opt/hp/storage_drivers Ported web release changes into 2.4.50. Enhancements Added the following: cciss binary support for Opteron. Smart Array 6i support. Support for Linux distributions and errata kernels. Support for Modular Smart Array 500 G2. Support for Modular Smart Array 20. Support for One Button Disaster Recovery (OBDR) with Smart Array. Logic to install scripts to warn user when driver versions are the same or newer than the driver to be installed. Kernels supported to the rpm release notes file. Kernels supported to the driver update diskette release note file. Monitor thread support to the rpm drivers. Beta errata for Red Hat Enterprise Linux 2.1 U4 and Red Hat Enterprise Linux 3 U2. ******************************** cpq_cciss-2.4.50-26.rhel3.amd64.rpm - ProLiant Linux driver (AMD64) for Smart Array 6i, 64xx, 5i, 5300 Series controllers for Red Hat Enterprise Linux 3 (AMD64/EM64T), v2.4.50-26 Fixes Resolved the following: bcm5700 6.2.17a fails to load on base SUSE Linux Enterprise Server 7 kernel. CPQ_CISS v.2.4.48-4 causes Boot menu to default to HP-2.4.7-4GB but kernel is actually 2.4.64GB-SMP. Default initrd incorrect should be SMP/enterprise but is set to UP. Issue in install script that prevented cciss.o driver from being backed-up on SUSE systems. Issue where drivers where not being installed properly on Red Hat Enterprise Linux 3 systems. Uninstall issue with UnitedLinux 1.0 and Red Hat Enterprise Linux 2.1. GRUB naming issue with UnitedLinux 1.0. Install issue to allow an initial ram disk to be built for newly installed binary errata kernels in the situation where the hardware is not supported by the driver found in the kernel. Cylinder calculation issue for filesystems greater than 502GB. Updated the following: rpm install script to avoid making a new initrd when the new drive is found to be the same as the existing one. Variable type to cover cases when the logical volume size is >1TB. To enable pre-fetch in the SCSI core for Smart Array for x86 architecture only. Required for firmware >= 1.86. Install script to allow rpm to build an initrd for smp or bigmem kernels even if the hardware is not smp or bigmem. Changed driver backup directory to /usr/src/HP/driver_backup. The default prefix for the storage rpm to /opt/hp/storage_drivers. changed DMA64 to DMA32 for cciss on Red Hat Enterprise Linux 2.1 to avoid data corruption on systems with 8GB of memory. Ported web release changes into 2.4.50. Enhancements Added the following: cciss binary support for Opteron. Smart Array 6i support. Support for Linux distributions and errata kernels. Support for Modular Smart Array 500 G2. Support for Modular Smart Array 20. Support for One Button Disaster Recovery (OBDR) with Smart Array. Logic to install scripts to warn user when driver versions are the same or newer than the driver to be installed. Kernels supported to the rpm release notes file. Kernels supported to the driver update diskette release note file. Monitor thread support to the rpm drivers. Conversion function for 32-bit user space apps to run on x86_64. /etc/init.d/cciss_hotplug script to rescan scsi bus. Support for 64bit (Intel em64t and AMD Opteron) Linux. RPM install code to insure AMD drivers land on AMD systems and Intel drivers land on Intel systems. ******************************** cpq_cciss-2.4.50-26.rhel3.em64t.rpm - ProLiant Linux driver (EM64T) for Smart Array 6i, 64xx, 5i, 5300 Series controllers for Red Hat Enterprise Linux 3 (AMD64/EM64T), v2.4.50-26 Fixes Resolved the following: bcm5700 6.2.17a fails to load on base SUSE Linux Enterprise Server 7 kernel. CPQ_CISS v.2.4.48-4 causes Boot menu to default to HP-2.4.7-4GB but kernel is actually 2.4.64GB-SMP. Default initrd incorrect should be SMP/enterprise but is set to UP. Issue in install script that prevented cciss.o driver from being backed-up on SuSE systems. Issue where drivers where not being installed properly on Red Hat Enterprise Linux 3 systems. Uninstall issue with UnitedLinux 1.0 and Red Hat Enterprise Linux 2.1. GRUB naming issue with UnitedLinux 1.0. Install issue to allow an initial ram disk to be built for newly installed binary errata kernels in the situation where the hardware is not supported by the driver found in the kernel. Cylinder calculation issue for filesystems greater than 502GB. Updated the following: rpm install script to avoid making a new initrd when the new drive is found to be the same as the existing one. Variable type to cover cases when the logical volume size is >1TB. To enable pre-fetch in the SCSI core for Smart Array for x86 architecture only. Required for firmware >= 1.86. Install script to allow rpm to build an initrd for smp or bigmem kernels even if the hardware is not smp or bigmem. Changed driver backup directory to /usr/src/HP/driver_backup. The default prefix for the storage rpm to /opt/hp/storage_drivers. changed DMA64 to DMA32 for cciss on Red Hat Enterprise Linux 2.1 to avoid data corruption on systems with 8GB of memory. Ported web release changes into 2.4.50. Enhancements Added the following: cciss binary support for Opteron. Smart Array 6i support. Support for Linux distributions and errata kernels. Support for Modular Smart Array 500 G2. Support for Modular Smart Array 20. Support for One Button Disaster Recovery (OBDR) with Smart Array. Logic to install scripts to warn user when driver versions are the same or newer than the driver to be installed. Kernels supported to the rpm release notes file. Kernels supported to the driver update diskette release note file. Monitor thread support to the rpm drivers. Conversion function for 32-bit user space apps to run on x86_64. /etc/init.d/cciss_hotplug script to rescan scsi bus. Support for 64bit (Intel em64t and AMD Opteron) Linux. RPM install code to insure AMD drivers land on AMD systems and Intel drivers land on Intel systems. ******************************** ProLiant Linux driver (AMD32) for Smart Array 6i, 64xx, 5i, 5300 Series controllers for Red Hat Enterprise Linux 3 (x86), v2.4.50-26 cpq_cciss-2.4.50-26.rhel3.amd32.rpm Enhancements Initial release. ******************************** hpdiags-6.3.0-15.linux.i386.rpm - HP Insight Diagnostics Online Edition for Linux, v6.3.0-15 Enhancements Initial release. ******************************** cmanic-7.1.1-5.linux.i686.rpm - NIC Agents for Servers - Linux, v7.1.1-5 Enhancements This Agent now runs in 64-bit kernel environments as noted in supported Operating Systems list. This Agent is updated to work with latest Health Driver (hpasm). ******************************** e100-2.3.40.2a-1.src.rpm - HP ProLiant NC31xx Fast Ethernet NIC Driver for Linux, v2.3.40.2a-1 Enhancements This driver now supports SUSE LINUX Enterprise Server 9. This driver no longer supports the /proc file system, which allows it to interact properly with the Linux SNMP Agents. ******************************** e1000-5.2.39.1c-1.src.rpm - HP ProLiant NC 61xx/71xx/310x Gigabit Ethernet NIC Driver for Linux, v5.2.39.1c-1 Enhancements The following ETHTOOL ioctls are now supported in this driver: ETHTOOL_SPAUSEPARAM ETHTOOL_GPAUSEPARAM ETHTOOL_SRXCSUM ETHTOOL_GRXCSUM ETHTOOL_GTXCSUM ETHTOOL_STXCSUM ETHTOOL_GSG ETHTOOL_SSG This driver now supports the HP NC310F Gigabit Server Adapter. This driver now supports SUSE LINUX Enterprise Server 9. This driver no longer supports the /proc file system, which allows it to interact properly with the Linux SNMP Agents. ******************************** bcm5700-7.2.24e-1.src.rpm - HP ProLiant NC 10xx/67xx/77xx/150x/320x Gigabit Ethernet NIC Driver for Linux, v7.2.24e-1 Fixes This driver resolves the following: Driver crashes during a transmit timeout reset. Data miscompare issues experienced with large ping packets. Enhancements This driver now supports SUSE LINUX Enterprise Server 9. This driver now supports the NC 150T PCI 4-port Gigabit Combo Switch Adapter. This driver adds some additional reported values to ETHTOOL_GSTATS. ******************************** vlan-1.8.0d-14.src.rpm - HP Tested and Approved Linux 802.1q VLAN Driver, v1.8.0d-14 Fixes Modified the vlan.conf file to be more general for both 2.4 and 2.6 kernels. If the VLAN is automated using the vlan.conf file, the VLAN is configured after a reboot. Modified the vlan.txt file to correct the placement of infenslave instructions. Updated to add protection against errors resulting from attempted removal of a failed or non-existing interface. Enhancements Added support for the following: NC 310F Gigabit Server Adapter SUSE LINUX Enterprise Server 9 and the 2.6 kernel. NC 150T PCI 4-port Gigabit Combo Switch Adapter. ******************************** cpqacuxe-7.15-21.linux.rpm - HP Array Configuration Utility for Linux, v7.15-21 Enhancements Release for installation on supported 64-bit Operating Systems. ******************************** Copyright 2003-2004 Hewlett-Packard Development Company, L.P.